Product Description The EP330 series is a NG-PON2 Optical Power Meter equipped with high-resolution photodetectors to make single-wave and pass-through measurements for upstream and downstream signals. For upstream signals, it can also perform burst light power measurement. With Wi-Fi and USB connectivity, you can remotely run tests, examine data, upload results, and more - all from your mobile device. The EP330 series is ideal for G-PON and NG-PON2 line detection and maintenance. Click here for more information:    Deviser EP330 Series Optical Power Meter

Product Description The AE1001 is a sleek, zero-fuss OTDR weighting less than 1kg that tests the common 1310nm and 1550nm wavelengths in 5s flat. Low power consumption and a solid 2500 mAh battery allows the AE1001 to run automated, manual, or real-time tests continuously for over 4 hours, and are supplemented with the handy OPM and VFL. Please click here for more information: Deviser AE1001 Portable OTDR

Product Description The TBL5016-1 50µH LISN is a device required to setup conducted noise measurements of DC or AC-powered electronic equipment. It is designed according to CISPR 16-1-2 and MIL-STD-461F standard and characterized in the frequency range of 9kHz to 100 MHz. Apart from carrying out conducted noise measurements, LISNs are also used to establish a defined impedance for various other standardized tests. The LISN is a 50Ω/50µH+5 Ω single line design with a high current jumper to short the 5 Ohm resistor and configure it as 50Ω/50µH LISN according to CISPR 16-1-2. The LISN is characterized up to 100 MHz which means that the LISN can be used for the combined range of 9 kHz to 100 MHz. The LISN is inserted into the supply line of the DUT (Device Under Test). Conducted noise, which is present at the supply terminals of the DUT can be measured at the BNC connector using a spectrum analyzer or a measurement receiver. The source (supply) terminal and the DUT terminal are decoupled by a 50µH inductor. DC or single phase measurements typically require a pair of TBL5016-1. Combining it with the Tekbox LISN Mate enables separate measurement of common mode and differential mode noise. DUTs with 3 phase supply require three or four pieces of TBL0516-1, depending on whether the product is supplied in delta or star configuration. The unit comes equipped with a BNC-male to N-male RG232 cable, mating connectors, high current configuration jumpers and ground brackets to attach it to a ground plane. Specifications LISN type: V-AMN, configurable as 50Ω/50µH+5 Ω or 50Ω/50µH Frequency range: 9 kHz – 100 MHz DC Resistance: < 45 mΩ Maximum current: 16A continuous Operating voltage range: 0 – 250V DC; 0 – 250V AC (50/60 Hz), 0 – 120V AC (400 Hz) Fuse: 2 x 16A slow High current plug/screw terminals – male: Phoenix Contact 1998933, female: Phoenix Contact 1967375 Dimensions: 250 mm x 225 mm x 140 mm (including ground brackets) weight: 2.7 kg

Product Description The Rigol Rigol DS1202Z-E is a very high quality two channel digital storage oscilloscope. It features a real-time sample rate of up to 1 GSa/s and a bandwidth of 200 MHz. The Rigol DS1202Z-E is equipped with well designed and easy to use control panels offering comprehensive ease-of-use functions for all measuring tasks. The menu navigation is intuitive and available in several languages. This high performance standard not only ensures capturing real-time instantaneous signals, but also observes details of repeated signals. The Rigol DS1202Z-E has a refresh rate of up to 30.000 wfms/s, enabling users to capture instantaneous signals, as well as abnormal signals more quicky. It also helps to enhance the waveform capturing ability and to expedite a circuit debug course. The quality of the Rigol oscilloscopes is comparable to Agilent and Tektronix oscilloscopes. The particularly large TFT color displays are very easy to read. Thanks to an intelligent system for displaying or masking information, the largest possible area is always available for displaying signals. The signal curves, the FFT display, and other functions can be shown simultaneously on the display. 200 MHz Digital Oscilloscope with 2 channels, 1GS/s, 24Mpoint memory High performance at an outstanding price Two channels 200 MHz bandwidth Real-time sample rate up to 1 GSa/s Memory depth up to 24 Mpts Up to 30,000 wfms/s waveform capture rate Up to 60,000 frames hardware real-time waveform recording and playback functions Various trigger and bus decoding functions Various interfaces: USB Host and Device, LAN (LXI), AUX Compact size, light weight, easy to use 7 inch WVGA (800x480) TFT LCD, intensity graded color display

Product Description B series is an efficient, budget-friendly and completely equipped infrared camera. This robust and very handy high-tech system thanks to its intuitively learnable handling and user-friendly single hand operation, which makes it an ideal tool for troubleshooting electrical installations, mechanical components, buildings, process equipment, HVAC/R equipment and others. Features · 3.5” large screen with no image cropping, high brightness screen to show image with no detailed information lost even outdoor or in highlight · Friendly UI, easy to use without training · Four image presentations--IR, visible, PIP and MIF Rugged and compact design, metal internal structure · Standard Micro USB interface for data transmission and charging · Removable Large capacity Li-ion battery, 4 hour working time · Optional Wi-Fi connection with notebook or mobile · Multi native charging model is selectable(the adapter/computer/car charger/dual battery charger) · Standard accessories: Thermal camera/ Li-ion Battery/ USB power supply with multi plugs/ USB cable/ Adapter/ User's manual/ Product CD/ SD card/ Wrist strap · Optional accessories: Camera carring pouch/ Battery charger/ Li-ion Battery Parameter B   Series B160V  B256V  B320V  Imaging Performance IR resolution 160×120  256×192  320×240  NETD ≤50mk Focal Length 5mm/F1.2 7mm/F1.1 7mm/F1.1 FOV 30°×23°  34.5°×26.5° 42.5°×32.5°  IFOV 3.30mrad 2.36mrad 2.33mrad Frame rate 25Hz/9Hz Focus fixed Detector Detector type VOx/7.5~14μm Pixel size 17μm Visible light  Resolution 640×480,   Automatic Image Presentation Display 3.5"   highlight LCD screen, 320×240 Image modes IR   image，Visible image，MIF，PIP Digital zoom ×2，×4  Color palettes 6 Measurement  Temperature range -20℃~350℃  Accuracy ±2℃ or   ±2% of reading for ambient   temperature 15℃ to 35℃ and object   temperature above 0℃ Measurement Analysis Spotmeter Center   spot Auto tracking Area   Tmax/Tmin tracking Emissivity correction Variable   from 0.01 to 1.00 Alarm Area   Tmax/Tmin alarms Storage Storage medium Removable   SD card（16G） Image format JPG   with temp info Video Streaming transferred   to via USB Interface Interface Micro   USB（for real-time image/ video   transmission）  WIFI Yes（for   data transfer and camera control）  Power System Battery Rechargeable   Li-ion battery, ≥4h, Automatic shut-down and   sleeping mode Environmental Parameters Operating temp range -10℃~50℃ Storage temp range -40℃~70℃ Encapsulation IP43，1m   drop Humidity 10% ~   95% Shock 30g （   IEC 60068-2-27 ） Vibration 10HZ~150HZ~10HZ   0.15mm    IEC60068-2-6  Weight 740g（batterry   included） Size 258mm×98mm×90mm

Product Description WavePro HD High-Definition oscilloscopes employ unique Teledyne LeCroy HD4096 technology to achieve 12-bit resolution at up to 8 GHz bandwidth, for the lowest noise and unmatched signal fidelity. Up to 5 Gpt of highly responsive acquisition memory gives more visibility into system behavior, and the exceptional analysis toolbox enables deep insight. Key Features HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s Up to 5 Gpts of acquisition memory enables detailed viewing of long events 15.6" 1900 x 1080 Full HD capacitive touchscreen New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector MAUI with OneTouch user interface for intuitive and efficient operation Deep toolbox enables and simplifies complex analysis Intuitive navigation to quickly find important features in long waveforms   HD4096 High Definition Technology Next-generation Teledyne LeCroy HD4096 technology enables capture and display of signals with 16 times more resolution than other oscilloscopes, up to 8 GHz bandwidth and 20 GS/s sample rate. Waveforms captured and displayed are cleaner and crisper. Signal details often lost in the noise on other oscilloscopes are clearly visible and easy to distinguish with HD4096. HD4096 enables oscilloscopes to deliver unmatched measurement precision for improved debug and analysis. High-resolution performance comes with no special operating modes or compromises on bandwidth or sample rate. 5 Gpt Acquisition Memory With up to 5 Gpts of acquisition memory, WavePro HD 12-bit oscilloscopes capture events occurring over long periods of time, while still maintaining high sample rate for visibility into the smallest details. A sophisticated acquisition and memory management architecture makes even the longest acquisitions fast and responsive. WavePro HD can capture 250 ms of data at full 20 GS/s sample rate - and always with 12 bits of resolution. Oscilloscopes with less memory require trading off sample rate for acquisition time. Powerful, Deep Toolbox WavePro HD features the comprehensive toolset common to all Teledyne LeCroy oscilloscopes. Measurements, math functions, analysis packages and advanced documentation features are all tightly integrated, and simple to use both independently and as part of a more sophisticated measurement setup. ProBus2 Probe Interface To fully realize the benefits of 8 GHz bandwidth at 12-bit resolution, WavePro HD features the ProBus2 probe interface. Based around a fully BNC-compatible connector with 8 GHz bandwidth, ProBus2 inputs can accept new ProBus2 probes up to 8 GHz, direct 50Ω coaxial connections, a wide variety of existing ProBus voltage and current probes, and passive probes requiring 1MΩ coupling. Deeply Embedded Computing Systems Testing WavePro HD has unsurpassed capabilities to acquire the longest records at the highest resolution for the most comprehensive deeply embedded computing system (analog, digital, serial data and sensor) testing. Comprehensive low-speed serial data triggers and decoders, plus measure/ graph and eye diagram testing provide the best causal analysis. Power Integrity Test WavePro HD's combination of high bandwidth and high resolution provides the capability to validate and debug all aspects of power supply, delivery and consumption - ensuring complete confidence. High bandwidth means accurate characterization of high-speed on-die effects such as ground bounce, while exceptionally low noise enables identification and root-cause analysis of low-level noise sources. Sensitive measurements such as rail collapse characterization can be made with complete confidence thanks to WavePro HD's high dynamic range and 0.5% gain accuracy. Serial Data Jitter and Noise Analysis WavePro HD 12-bit oscilloscopes bring the high signal fidelity of HD4096 technology to high-speed serial data analysis. 12-bit resolution, exceptionally low noise and 60 fs timebase jitter mean a low jitter measurement floor, for the most accurate serial data jitter and noise measurements possible. SDAIII CompleteLinQ provides the most complete set of serial data analysis tools available, and user-friendly QualiPHY options greatly simplify complex compliance testing. Electromagnetic Compatibility (EMC/EMI) WavePro HD 12-bit oscilloscopes' high sample rate and long memory combine with Teledyne LeCroy's dedicated EMC pulse parameter package to accurately characterize EMC test signals. Fast pulse rise times may require 2.5 to 4 GHz bandwidth at very high sample rates to ensure measurement confidence. WavePro HD provides the most accurate characterization using 20 GS/s sample rate, 12-bit resolution, and 0.5% gain accuracy. Main Specifications Bandwidth 2.5 GHz - 8 GHz Memory 100 Mpts - 5 Gpts Max Memory 5 Gpts Max Sampling Rate 20 GS/s Input Channels 4 Resolution 12-bit WavePro 254HD WavePro 404HD WavePro 604HD WavePro 804HD WavePro 254HD-MS WavePro 404HD-MS WavePro 604HD-MS WavePro 804HD-MS

Product Description HDO6000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug, troubleshooting, and deep analysis of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs. Key Features 4 input channels 16 digital channels (with –MS models) 12-bit ADC resolution, up to 15 bits with enhanced resolution Up to 10 GS/s with Enhanced Sample Rate 350 MHz, 500 MHz, and 1 GHz bandwidths ±10 V applied offset with high gain settings Long Memory - up to 250 Mpts/Ch MAUI with OneTouch user interface Exceptional Serial Data Tools Powerful, Deep Toolbox   HD4096 High Definition Technology Enables capture and display of signals with 16 times more resolution than other oscilloscopes. Waveforms captured and displayed are cleaner and crisper. Signal details often lost in the noise on other oscilloscopes are clearly visible and easy to distinguish with HD4096. HD4096 enables oscilloscopes to deliver unmatched measurement precision for improved debug and analysis. Huge Applied Offset Range A 16-bit offset DAC permits ±10 V offset at 20 mV/div, ±4 V at 5 mV/div, and an amazing ±1.6 V offset at the highest sensitivity (1 mV/div). Such large applied offsets (combined with 12 bits) make it easy to acquire and view small signal variations (e.g. ripple, noise, transient interference) on DC or sensor signals. They also provide extended offset ranges for many of Teledyne LeCroy’s high voltage probes . MAUI with OneTouch MAUI – Most Advanced User Interface puts all the power and capabilities of the oscilloscope right at your fingertips. Designed for touch, built for simplicity, and made to solve. MAUI with OneTouch incorporates drag, drop and flick to provide unsurpassed efficiency in oscilloscope operation. Learn more about MAUI Exceptional Serial Data Tools Up to 23 standards supported – all with the industry’s best serial decoder. Many are provided with high performance triggers, unique measure and graph tools for validation efficiency (including a software serial DAC), and eye diagrams and physical layer testing tools. Learn more at teledynelecroy.com/tdme Powerful, Deep Toolbox Our waveshape analysis tools and application packages provide unparalleled insight. Learn more at Periodic Table of Oscilloscope Tools. Combine our powerful, deep toolbox with up to 250 Mpts/ch of acquisition memory and the most powerful motherboard in its class – an Intel® Core™ i7-2710QE Quad (core), 3.0 GHz (per core, in turbo mode), with 16 GB of RAM standard. Main Specifications Bandwidth 350 MHz - 1 GHz Memory 50 Mpts - 250 Mpts Max Sampling Rate 10 GS/s Input Channels 4 Resolution 12-bit

Product Description HDO4000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug and troubleshooting of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs. Key Features 4 input channels 16 digital channels (with –MS models) 12-bit ADC resolution, up to 15 bits with enhanced resolution Up to 10 GS/s with Enhanced Sample Rate 200 MHz, 350 MHz, 500 MHz, and 1 GHz bandwidths ±10 V applied offset with high gain settings Long Memory - up to 50 Mpts/Ch MAUI with OneTouch user interface Exceptional Serial Data Tools Powerful, Deep Toolbox HD4096 High Definition Technology Enables capture and display of signals with 16 times more resolution than other oscilloscopes. Waveforms captured and displayed are cleaner and crisper. Signal details often lost in the noise on other oscilloscopes are clearly visible and easy to distinguish with HD4096. HD4096 enables oscilloscopes to deliver unmatched measurement precision for improved debug and analysis. Huge Applied Offset Range A 16-bit offset DAC permits ±10 V offset at 20 mV/div, ±4 V at 5 mV/div, and an amazing ±1.6 V offset at the highest sensitivity (1 mV/div). Such large applied offsets (combined with 12 bits) make it easy to acquire and view small signal variations (e.g. ripple, noise, transient interference) on DC or sensor signals. They also provide extended offset ranges for many of Teledyne LeCroy’s high voltage probes. MAUI with OneTouch MAUI – Most Advanced User Interface puts all the power and capabilities of the oscilloscope right at your fingertips. Designed for touch, built for simplicity, and made to solve. MAUI with OneTouch incorporates drag, drop and flick to provide unsurpassed efficiency in oscilloscope operation. Learn more about MAUI. Exceptional Serial Data Tools Up to 23 standards supported – all with the industry’s best serial decoder with. Many are provided with high performance triggers. Learn more at teledynelecroy.com/tdme Powerful, Deep Toolbox Our waveshape analysis tools and application packages provide unparalleled insight. Learn more at Periodic Table of Oscilloscope Tools. Combine our powerful, deep toolbox with up to 50 Mpts/ch of acquisition memory and the most powerful motherboard in its class – an Intel® Core™ i3-2330E Dual (core), 2.2 GHz (per core) with 8 GB of RAM standard Main Specifications Bandwidth 200 MHz - 1 GHz Memory 12.5 Mpts - 25 Mpts Max Sampling Rate 10 GS/s Input Channels 4 Resolution 12-bit

Product Description The TBCP1-200 is a fixed aperture RF current monitoring probe, expanding the Tekbox product range of affordable EMC pre-compliance test equipment.The probe has a 3dB bandwidth of approximately 200 MHz and is characterized and usable over the frequency range from 10kHz to 500 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.   The TBCP1-250 is a fixed aperture RF current monitoring probe, expanding the Tekbox product range of affordable EMC pre-compliance test equipment.The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized and usable over the frequency range from 30kHz to 250 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 16 dB Ohm in the range from 300 kHz to 250 MHz. Specifications TBCP1-200 Characterized frequency range: 10 kHz to 500 MHz Aperture diameter: 25 mm Outside diameter: 76 mm Height: 31 mm Weight: 320 g Connector type: N female Transfer impedance: 3 to 17 dBΩ Max. primary current (DC – 400 Hz): 80 A Max. primary current (RF): 3 A Max. core temperature: 125 °C TBCP1-250 Characterized frequency range: 30 kHz to 250 MHz Aperture diameter: 25 mm Outside diameter: 76 mm Height: 31 mm Weight: 320 g Connector type: N female Transfer impedance: 0 to 18 dBΩ Max. primary current (DC – 400 Hz): 80 A Max. primary current (RF): 3 A Max. core temperature: 125 °C

Product Description SecuriTEST IP is an installation and troubleshooting tester for digital/IP, HD coax and analogue CCTV camera systems. With a single tester that can power, configure and document, SecuriTEST IP increases productivity from start to finish. Connect to various cameras using RJ45, Wi-Fi or BNC ports Power the camera with 12V from the Li-Ion battery or PoE/PoE+ Faster camera login using the unique QuickIP™ function Comprehensive camera setup with aim, focus, PTZ, presets and network settings Provide proof of installation with PDF reports that show camera parameters and multiple video screen-shots Eliminate guess work with data cable and network troubleshooting tools Brochure Datasheet

Description The MSO5000 Series Oscilloscopes combine best in class sampling and memory depth with our modern, flexible User Interface enabled by our new UltraVision II architecture and innovative Phoenix Chipset. With 70 to 350 MHz models each with 2 or 4 analog channels, the MSO5000 Series brings innovative flexibility and capability to the engineer’s bench. Analyze your critical signals with zone triggering, 7 instruments in 1, Enhanced FFTs, color grading, and histograms all supported by the high sample rate, deep memory, and full memory measurements.  Specifications MSO 5000 Datasheet & Specs Rigol MSO5072 (70MHz - 2Channel) Rigol MSO5074 (70MHz- 4Channel) Rigol MSO5102 (100MHz- 2Channel) Rigol MSO5104(100MHz-4 Channel) Rigol MSO5204 (200MHz-4 Channel) Rigol MSO5354 (350MHz-4 Channel)

Description Product Overview SPD1000X Programmable Linear DC Power Supply has a 2.8 inch TFT-LCD display, features remote computer control capability,  and real time wave display, to deliver high performance and ease-of-use. The SPD1168X features a high precision programmable output capable of delivering up to 16 V ,theSPD1305X features a high precision programmable output capable of delivering up to 30 V and also includes a 4-wire sense function for more accurate voltage sourcing, especially for long leads or high resistance connections. There are additional output short and overload protect functions to assist in production and development applications. Key Features ▶ Single path high-precision programmable voltage output：     SPD1168X——16 V/8 A，total power up to 128 W     SPD1305X——30 V/5 A，total power up to 150 W ▶ Stable, reliable, Low ripple and noise：≤ 350 uVrms/3 mVpp; < 2 mArms ▶ Fast transient response time: < 50 μs ▶ 5 digit Voltage, 4 digit Current Display, Minimum Resolution: 1 mV/1 mA ▶ Supports front panel timing output functions ▶ 2.8 inch true color TFT- LCD 240 *320 display ▶ 2 types of output modes：Two-wire output mode, 4-wire compensation output mode，Maximum compensation voltage 1V ▶ 100/120/220/230 V compatible design to meet the needs of different power grids ▶ Intelligent temperature-controlled fanreduces noise ▶ Clear graphical interface, with the waveform display function  ▶ Internal 5 groups of system parameter save/recall ▶ Includes PC software: Easypower, supports SCPI, LabView driver Characteristics ▶ High-resolution and high-precision output The SPD1000X power supply features a high measurement resolution of 1mV/1mA . This ensures accurate output even with very with small changes in voltage or current. This is impossible for a low resolution power supply. ▶ 4-wire SENSE compensation mode function In the 4-wire SENSE compensation output mode: By using a separate measurement circuit, the supply can more accurately compensate for any voltage ｄｒｏｐs due to high resistance connections or long cables. Maximum compensation voltage is 1V Product No : Product information SPD1168X SPD1305X Single path independent output, min resolution 1 mV/1 mA, USB Device & LAN, 2.8 inch LCD display Standard Accessories USB Cable -1  Quick Start -1 Calibration Certificate -1 Power cord -1 Output Test Cord -2 Sets 《SPD1000X Series Programmable DC Power Supply Datasheet》

Product Overview Engineers and students who require high signal fidelity in a reliable and capable waveform generation need look no further than the DG900 Series generators. With frequencies up to 100 MHz, 16Bit Resolution, and arbitrary waveforms of up to 16 Mpts the DG900 reproduces any waveform with high signal fidelity.  SiFi II adds additional filtering capabilities making this one of the most flexible generators on the market.  The intuitive touchscreen control and compact fanless design make it the perfect choice for your desk, bench, or lab. DG900 SeriesHigh Resolution Waveform Generation 16 Bit resolution Intuitive Touch Screen design 50 to 100 MHz frequency ranges by model Fanless silent operation 16 MPts  arbitrary memory Enhanced Waveform modes with SiFi II technology 2 channels Specification Model DG952 DG972 DG992 Channel 2 2 2 Max. Frequencey 50 MHz 70 MHz 100 MHz Sample Rate 250 MSa/s

Product Description New from Deviser Instruments, the TC602RE is a handheld Ethernet backhaul service tester that supports testing for speeds up to 1Gbps. The TC602RE adds a suite of E1,SyncE, and IEEE 1588v2 testing functions for even wider utility. It's the next generation of telecommunication systems analysis, serving the growing need for high-speed metropolitan access at unmatched cost performance. • 5 inch TFT LCD touch screen(800x480)• Complete solution for activating, verifying & fault-diagnosing Ethernet service from 10Mbit/s to 1Gbit/s quickly and easily• Integrates multiple software tools for field measurement,ensuring high cost-performance• 75Ω unbalanced BNC×2, 120Ω balanced RJ48×1• LOS, LOF, and AIS warring measurement• 2.048 Mbit/s transmit and receive Applications: The TC602RE Ethernet Backhaul and E1 Tester excels at all Ethernet measurement applications, including performance evaluation; metro Ethernet installation, activation, & maintenance; point-to- point Ethernet joining-up service planning; real-time online fault diagnosis;wireless backhaul service verification and more. Ethernet Features: • Supports two 10/100/1000Base-T electrical interface and two 1000Base-X optical interface• Synchronous Ethernet (SyncE) and IEEE 1588v2 (Precision Time Protocol) measurement• RFC 2544: Throughput, Latency, Packet Delay Variation, Frame Loss, and Back-to-Back (symmetrical and asymmetric results)• Ethernet BERT: Layer 1 to Layer 4• Y.1564: Service configuration & performance measurement• Stream traffic generation and analysis up to 10 streams• Smart Loopback for Layer 1 to Layer 4• VLAN (Q-in-Q) support• MPLS support• Packet Delay Variation measurement• Cable Diagnostics and Optical Power testing• IPv6 support• Ping, Trace Route• CSV and PDF result files• E1 Features:• 2.048 Mbit/s transmit and receive• ITU-T G.821, G.826, and M.2100• LOS, LOF, and AIS warring measurement• 75Ω unbalanced and 120Ω balanced support• Error injection / alarm generation

Product Description The SIGLENT SVA1000X series spectrum & vector network analyzers are powerful and flexible tools for broadcast and RF device testing. With a wide frequency range from 9 kHz to 1.5 GHz, the analyzer delivers reliable automatic measurements and plenty of features including a tracking generator and multiple modes of operation: the base model is a swept super-heterodyne spectrum analyzer and optional functions include a vector network analyzer, a Frequency Domain Reflectometer based distance-to-fault locator, and a modulation analyzer. Applications include broadcast monitoring/evaluation, site surveying, EMI pre-compliance, research and development, education, production and maintenance. Key Features ◆ All-Digital IF TechnologyAll-Digital IF Technology ◆ Frequency Range from 9 kHz to 1.5 GHz ◆ -156 dBm/Hz Displayed Average Noise Level (Typ.)◆ -99 dBc/Hz @10 kHz Offset Phase Noise (1 GHz, Typ.)◆ Level Measurement Uncertainty < 1.2 dB (Typ.)◆ 1 Hz Minimum Resolution Bandwidth (RBW)◆ Preamplifer Standard◆ Tracking Generator Standard◆ Vector Network Analysis (Opt.)◆ Distance To Fault (Opt.)◆ Modulation Analysis (Opt.)◆ EMI Pre-compliance Test Kit (Opt.)◆ Advanced Measurement Kit (Opt.) ◆ 10.1 lnch (1024x600) Multi-Touch Screen, Mouse and Keyboard supported◆ Web Browser Remote Control on PC and Mobile Terminals 

Product Description SIGLENT’s new SDS1000X-E Super Phosphor Oscilloscopes feature two channel and four channel models. The two channel model is available with a 200 MHz analog bandwidth, a single ADC with a 1 GSa/s maximum sample rate, and a single memory module with 14 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease -of -use, the most commonly used functions can be accessed with its user- friendly front panel design.  The SDS1000X-E series employs a new generation of SPO (Super -Phosphor Oscilloscope) technology that provides excellent signal fidelity and performance. The system noise is also lower than similar products in the industry. It comes with a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). The SDS1000X-E also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. SIGLENT’s latest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering. Serial bus decoding for IIC, SPI, UART, CAN, LIN bus types is included. The X-E models also include History waveform recording, and sequential triggering that enable extended waveform recording and analysis. Another powerful addition is the new 1 million point FFT math function that gives the SDS1000X-E very high frequency resolution when observing signal spectra. The new digital design also includes a hardware co-processor that delivers measurements quickly and accurately without slowing acquisition and front-panel response. The features and performance of SIGLENT’s new SDS1000X-E cannot be matched anyｗｈｅｒｅ else in this price class. The four channel series includes even more functions, including: searching and navigating, on-screen Bode plot, 16 digital channels (Option), an external USB powered 25 MHz AWG module (Option), a USB WIFI adapter (Option), and an embedded application that allows remote control via web browser. Key Features ◆ 100 MHz, 200 MHz bandwidth models ◆ Two channel series have one 1 GSa/s ADC, four channel series have two 1 GSa/s ADCs. When all channels are enabled, each channel has a maximum sample rate of 500 MSa/s. When a single channel per ADC is active, it has sample rate of 1 GSa/s ◆ The newest generation of SPO technology    ◆ Waveform capture rate up to 100,000 wfm/s (normal mode), and 400,000 wfm/s (sequence mode)    ◆ Supports 256-level intensity grading and color display modes     ◆ Record length up to 14 Mpts    ◆  Digital trigger system ◆ Intelligent trigger: Edge, Slope, Pulse Width, Window, Runt, Interval, Time out (Dropout), Pattern ◆ Serial bus triggering and decoding (Standard), supports protocols IIC, SPI, UART, RS232, CAN, LIN ◆ Video trigger, supports HDTV ◆ Low background noisewith voltage scales from 500 μV/div to 10 V/div ◆10 types of one-button shortcuts, supports Auto Setup, Default, Cursors, Measure, Roll, History, Display/Persist, Clear Sweep, Zoom and Print ◆ Segmented acquisition (Sequence) mode, divides the maximum record length into multiple segments (up to 80,000), according to trigger conditions set by the user, with a very small dead time segment to capture the qualifying event. ◆ History waveform record (History) function, maximum recorded waveform length is 80,000 frames. ◆ Automatic measurement function for 38 parameters as well as Measurement Statistics, Zoom, Gating, Math, History and Reference functions ◆ 1 Mpts FFT ◆ Math and measurement functions use all sampled data points (up to 14 Mpts) ◆ Math functions (FFT, addition, subtraction, multiplication,division, integration, differential, square root) ◆ Security Erase modePreset key can be customized for user settings or factory “defaults” ◆ Security Erase mode ◆ High Speed hardware based Pass/ Fail function ◆ MSO, 16 digital channels (four channel series only, option) ◆ Bode plot (four channel series only) ◆ Search and navigate (four channel series only) ◆ USB AWG module (four channel series only, option) ◆ USB WIFI adapter (four channel series only, option) ◆ Web Browser based control (four channel series only) ◆ Large 7 inch TFT -LCD display with 800 * 480 resolution ◆ Multiple interface types: USB Host, USB Device (USB -TMC), LAN Pass / Fail, Trigger Out ◆ Supports SCPI remote control commands ◆ Supports Multi-language display and embedded online help SDS1000X-E Series Digital OscilloscopeSDS1104X-E 100 MHz Four ChannelsSDS1204X-E 200 MHz Four ChannelsSDS1202X-E 200 MHz Two Channels

Product Overview Siglent’s SPD3000X Series Programmable Linear DC Power Supply has a 4.3 inch TFT-LCD display, supports Remote Programming and has a Real Time Wave Display. The ‘3000X family has three isolated outputs; two adjustable channels and one selectable channel from 2.5v, 3.3V, and 5V. It also has output short and overload protection and can be used in production and development. Key Features ◆ 3 independently controlled and isolated outputs: 32V/3.2A×2, 2.5V/3.3V/5V/3.2A×1, total 220W ◆ 5 digits Voltage, 4 digits Current Display, Minimum Resolution: 1mV/1mA (SPD3303X) ◆ Supports front panel timing output functions ◆ 4.3 inch true color TFT- LCD 480x272 display ◆ 3 types of output modes: independent, series, parallel ◆ 100V/120V/220V/230V compatible design to meet the needs of different power grids. ◆ Intelligent temperature-controlled fan, effectively reduces noise ◆ Clear graphical interface, with waveform display function ◆ Five internal groups of system parameter save/recall, supports data storage space expansion ◆ Provides PC software; Easypower, supports SCPI, LabView drive Characteristics High-resolution / high-precision output The highest resolution of 1mV/1mA (SPD3303X), provides excellent setting and read back accuracy. This ensures accurate output even with very with small changes in voltage or current. This is impossible with a low resolution power supply. Series/parallel/independent mode functions Series and parallel functions allows for combining two channels into one output with more power output capability, extending the application range. Each of 3 channels power can be turned on or off independently and also can be turned all on or all off. Panel displays the timing output Through front panel operation, five groups of timing settings and output control can be displayed, which provides users with simple power programming functionality. Also, by connection to Siglent’s EasyPower PC software, a full range of communication and control features can be used. Save/Recall setting parameters The SPD3000X series programmable power supply can save or recall 5 groups of setting parameters in internal storage and also supports external storage expansion. Settings can be easily recalled if needed.

Product Overview SDS1000DL+ series is a dual-channel universal digital oscilloscope, available in 50 MHz, bandwidth models. It includes a 30 Kpts memory depth that helps to ensure accurate waveform resolution and to capture longer signal lengths. With its 7 inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 1 GSa/s sampling rate, the SDS1000CML+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements. Key Features ◆ 50 M Hz bandwidth models ◆ Real-time sampling rate up to 500 MSa/s, Equivalent-time sampling rate up to 50 GSa/s ◆ Memory Depth up to 30 Kpts ◆ Trigger types: Edge, Pulse, Video, Slope, Alternate ◆ Waveform math functions:+, -, *, /, FFT ◆ 6 digital frequency counter ◆ Supports Multi-language display and embedded online help ◆ Screensaver from 1 minute to 5 hours ◆ Digital filter and waveform recorder function ◆ Shortcut storage function key ◆ 7 inch TFT-LCD display with 800 * 480 resolution ◆ Multiple interfaces: USB Host, USB Device (USBTMC), LAN (VXI-11), Pass / Fail

Product Overview      SIGLENT’s new SDS1000X/SDS1000X+ Series Super Phosphor Oscilloscopes are available in two bandwidths, 100 MHz and 200 MHz, have a sampling rate of 1 GSa/s and a standard record length of 14 Mpts. The most commonly used functions can be accessed with its user-friendly one-button design. The SDS1000X/SDS1000X+ series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 60,000 frames/sec. It also employs not only the common 256-level intensity grading display function but also a color temperature display mode not found in other models in this class. Siglent’s new oscilloscopes offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. SDS1000X+ adds an integrated 25 MHz arbitrary waveform generator (standard), option for 16 digital channels. The features and high-performance of the SDS1000X/SDS1000X+ oscilloscopes cannot be matched at any product at this price. Key Features ◆200 MHz, 100 MHz bandwidth models ◆Real-time sampling rate up to 1GSa/s ◆New generation of SPO technology    ◆ Waveform capture rate up to 60,000 wfm/s (normal mode), and 400,000 wfm/s(sequence mode)    ◆ Supports 256-level intensity grading and color display modes    ◆ Record length up to 14 Mpts    ◆ Digital trigger system ◆Intelligent trigger: Edge, Slope, Pulse Width, Window, Runt, Interval, Time out (Dropout),Pattern ◆Serial bus triggering and decode, supports protocols IIC, SPI, UART, RS232, CAN, LIN ◆Video triggers and supports HDTV ◆Low background noise, supports 500μV / div to 10V / div voltage scales ◆10 types of one-button shortcuts, supports Auto Setup, Default, Cursors, Measure, Roll, History, Display/Persist, Clear Sweep, Zoom and Print ◆ Segmented acquisition (Sequence) mode, dividing the maximum record length into multiple segments (up to 80,000), according to trigger conditions set by the user, with a very small dead time segment to capture the qualifying event. ◆History waveform record (History) function, the maximum recorded waveform length is 80,000 frames ◆Automatic measurement function on 37 parameters, supports Statistics, Gating measurement, Math measurement, History measurement and Ref measurement ◆Math function (FFT, addition, subtraction, multiplication, division, integration, differential, square root) ◆ High Speed hardware based Pass/ Fail function ◆16 Digital channels (MSO), Maximum waveform capture rate up to 500 MSa/s, Record length up to 14 Mpts/CH (Option for SDS1000X+ models) ◆ 25 MHz DDS arbitrary waveform generator, built-in 10 kinds of waveforms (Standard for SDS1000X+ models) ◆ Large 8 inch TFT-LCD display with 800 * 480 resolution ◆ Multiple interface types: USB Host, USB Device (USB-TMC), LAN (VXI-11), Pass / Fail, Trigger Out ◆ Supports SCPI remote control commands ◆ Supports Multi-language display and embedded online help 《SDS1000X/X+ Series Super Phosphor Oscilloscopes Datasheet》 Ordering Information Product Name Product Description SDS1202X+ 200 MHz, 2 CH, Built-In Waveform Generator, 16 Digital Channels (Option) SDS1102X+ 100 MHz, 2 CH, Built-In Waveform Generator, 16 Digital Channels (Option) SDS1202X 200 MHz, 2 CH SDS1102X 100 MHz, 2 CH Standard Accessories USB Cable -1 Passive Probe -2 Power Cord -1 Quick Start -1 Certification -1 Optional Accessories SDS-1000X-DC I2C,SPI,UART/RS232,CAN,LIN Decoder  SDS-1000X-16LA 16 Channels MSO (Software)  SPL1016 16 Digital Channels Logic Probe ISFE Isolated Front End STB STB Demo Source HPB4010 High Voltage Probe CP4020/CP4050/CP4070/ CP4070A/CP5030/CP5030A/ CP5150/CP5500 Current Probe DPB4080/DPB5150/DPB5150A/ DPB5700/DPB5700A Differential Probe

Product Description Satlink WS-6916 DVB-S/S2 HD Satellite Finder with MPEG-2/MPEG-4 Satlink 6916 Meter 3.5 Inch High Definition TFT LCD ScreenFully DVB-S/S2, MPEG-2/MPEG4 compliantMPEG-2 / H.264 Hardware decodingDigital meter for signal strength and qualitySupports for multiple TP detectionSupports scan of Auto,Blind,Manual orNITSound and Light Alarm for Locking SignalAuto Calculate Angle of AZ ,ELSupports DISEQC 1.0/1.1/1.2 ,0/22khz ToneSpeaker IntegratedSupport both AV out and AV inSupports HDMI outLNB short protect7.4V/3000mAh Li-ion Battery IncludedSoftware upgrade via USB portEasy to carry

The Tekset01 Includes: Kim Wipes (280Pcs) Miller CFS2 Stripper Visual Fault Locator -1mW Ideal Kevlar Cutter One Click Cleaner 1.2mm (Cleans connectors and adapters) One Click Cleaner 2.5mm (Cleans connectors and adapters) Mills Stripper Cable (For Fibre and or Copper) Ideal Cable Slitter (Ringer Adjustable Blade) Alcohol Bottle (200ml twist lock -Alcohol Inc) Hard Tool Case

Product Description Engineers integrating WiFi, Bluetooth and other modern RF technologies are confronted with complex challenges like frequency hopping signals, channel conflict, and spectrum interference.  Real-Time Spectrum Analyzers bring the dimension of time to RF Analysis making it easier to monitor and characterize these complex RF systems.  The RSA5000 combines industry leading realtime performance (7.45µs 100% POI), rich data displays, and advanced triggering options allowing the user to quickly capture, identify and analyze these complex events.  Specifications • 9 kHz to 3.2 or 6.5 GHz Frequency Range • 10.1” Capacitive touchscreen display • Displayed Average Noise Level as low as -165 dBm with opt. PreAmplifier • Real-Time Analysis Bandwidth of 25 MHz standard (40 MHz option) • 7 Real-Time visualization modes • 100 % POI as low as 7. 45 µseconds • 1 Hz Minimum Resolution Bandwidth (RBW) • 1 ms full span sweep speed • EMI bandwidths standard (200 Hz, 9 kHz, 120 kHz, 1 MHz) Models Model Frequency DANL Phase Noise RBW RSA5032 3.2 GHz -165 dBm -108 dBc/Hz 1 Hz RSA5032-TG 3.2 GHz -165 dBm -108 dBc/Hz 1 Hz RSA5065 6.5 GHz -165 dBm -108 dBc/Hz 1 Hz RSA5065-TG 6.5 GHz -165 dBm -108 dBc/Hz 1 Hz Rigol RSA5000 Datasheet & Specs

Key Features & Specifications Optimize OPEX by streamlining analytics processes in a multivendor environment Vendor-neutral, multi-data analytics solution that provides the most comprehensive network analysis available in the market. Supports a wide range of data inputs, e.g. drive test data and Operations Support Systems (OSS) data One tool to process data from various tools from major measurement vendors Industry-leading desktop-based drive test data post-processing tool for radio access network analysis For network planning engineers, network performance engineers, handset testing groups, and technology development groups Easy to use, versatile Single-click option to load large amounts of data files Drag-and-drop based UI with dashboards for easy overview Processes large volumes of drive test data and/or walk test data with ease Multi-core processing functionality for faster data output and lesser wait times Multiple devices and data sets can be merged to create large data sets Designed for optimization, acceptance, and benchmarking of new technologies and high speed data networks Support for latest wireless technologies Wide application support Description Network analytics in a multivendor environment Nemo WindCatcher is the industry leading desktop-based drive test data post-processing tool for radio access network analysis used by design engineers, performance engineers, handset testing groups, and technology development groups. Support for all major data collection tools Nemo WindCatcher is a vendor-neutral, multi-data, multi-wireless access technology solution that provides the most comprehensive solution available in the market. It supports a wide range of data inputs and all major data collection tools on the market, and it is optimized for heterogeneous test environments and processes. Nemo WindCatcher is loaded with extremely robust out-of-the-box features for powerful data aggregation and analytical functionality, one-step analysis, and detailed reporting. Users can quickly identify and solve problems maximizing overall productivity and efficiency. Flexible in-depth analysis Wireless network operators can leverage Nemo WindCatcher to analyze large amounts of drive test data to enhance customer experience through efficient network optimization, new technology roll-out, and troubleshooting. Operators can deploy new technologies, such as LTE, LTE-A and Voice over LTE (VoLTE), using the advanced analytics in Nemo WindCatcher. Device manufacturers can use Nemo WindCatcher to modify the functionality of their devices for use in different network conditions. Small cell/Distributed Antenna Systems (DAS) and Call Trace features Nemo WindCatcher DAS/Small Cells module provides an efficient method for validating and testing multi-floor indoor venues, such as stadiums and airports, using a purpose-built project manager feature. In-building deployment teams can use Nemo WindCatcher to verify DAS implementations and generate reports for the commissioning of venues. Nemo WindCatcher Call Trace Data module processes call trace data from major infrastructure OEMs in native OSS format. It allows the analysis of coverage and quality KPIs and poor performance areas using geo located call trace data plots, heat maps, and customizable reports.

Product Overview SIGLENT SDG6000X is a series of dual-channel Pulse/ Arbitrary Waveform Generators that feature up to 500 MHz bandwidth, a maximum sample rate of 2.4 GSa/s and 16-bit vertical resolution. They also include proprietary TrueArb & EasyPulse technology that help to solve the weaknesses inherent in traditional DDS generators when generating arbitrary, square and pulse waveforms. In addition, the SDG6000X is a multi-function device which can generate Noise, IQ signals and PRBS patterns. These features enable the SDG6000X to provide a variety of high fidelity and low jitter signals, meeting the growing requirements of complex and intensive applications. Key Features  ▪ Dual-Channel, 500 MHz maximum bandwidth, 20 Vpp maximum output amplitude, high fidelity output with 80 dB dynamic range▪ High-performance sampling system with 2.4 GSa/s sampling rate and 16-bit vertical resolution▪ Multi-function signal generator, meeting requirements in wide range ▪ Sweep and Burst function▪ Harmonics function▪ Waveform Combining function▪ Channel Coupling, Copy and Tracking functionr▪ 196 built-in arbitrary waveforms ▪ High precision Frequency Counter▪ Standard interfaces include: USB Host, USB Device （USBTMC）, LAN（VXI-11, Socket, Telnet）. Optional Interface: GPIB▪ 4.3” touch screen display for easier operation Product Description SDG6052X 500 MHz, 2-CH, 2.4 GSa/s, 16-bit SDG6032X 350 MHz, 2-CH, 2.4 GSa/s, 16-bit SDG6022X200 MHz, 2-CH, 2.4 GSa/s, 16-bit Standard Configurations:Quick start ×1 Power cord ×1 Calibration Certificate ×1 USB cable ×1 BNC Coaxial Cable ×2 Optional ConfigurationsSPA1010  10W Power AmplifierATT-20dB  20 dB AttenuatorUSB-GPIB

Product Description The TBFL1 is a combined transient limiter / attenuator / high pass filter, designed to provide optimum protection of spectrum analyzer or measurement receiver inputs when carrying out conducted noise measurements or other measurements where the input levels cannot be predicted with certainty or where accidental overloads may occur.  Pin- and schottky diodes combined with a multi-stage 10dB attenuator result in a device which can withstand a continuous RF input level of up to 5W (37 dBm). A gas discharge tube provides additional protection against high voltage transients. Furthermore, a 9 kHz high pass filter suppresses harmonics of the mains supply voltage.  With a limiting threshold of +11dBm and a flat frequency response from 9 kHz to 600 MHz, the TBFL1 limiter can be used as protective device for the complete range of conducted noise measurements and in many other applications. Specifications Frequency range: 9 kHz - 600 MHz Attenuation: 10 dB - 0.5/+1.2 dB in-band (9 kHz to 600 MHz) Attenuation HP-filter: > 30 dB @ 2kHz Maximum continuous RF input power: 5W (+37 dBm) in-band Maximum DC input voltage: ± 20V Input matching, linear operating range: 9 kHz - 600 MHz < - 16 dB Output matching, linear operating range: 9 kHz - 600 MHz < - 23 dB Linear operating range: up to 0 dBm input level, in-band Limiting threshold: +11 dBm (@ 37dBm input level) Input connector: N-female Output connector: N-male Dimensions: 156 mm x 26 mm x 26mm Weight: 170 g Application General purpose RF transient limiter Transient limiter for conducted noise measurement set up

Product Description Chauvin Arnoux Model PEL 105 is a simple to use, power and energy data logger that monitors both traditional and renewable energy sources. It monitors and records True RMS voltage and current, power, energy, cost and harmonics locally or from anywhere in the world. The PEL 105 is built into a waterproof case with an IP67 rating designed for outdoor use and is ideal for pole mounting and can be powered from a phase being monitored. This product is perfect for electricians, engineers and contractors doing work in the areas of building and system monitoring and upgrades, including compliance to article 220.87 of the NEC, as well as overall energy audits and incoming power monitoring. It is available with an Android™ App to configure, view and capture data wirelessly. Bluetooth and Wi-Fi wireless communication provides the operator with the ability to work from a safe distance away from dangerous voltages and currents. Advantages 5 voltage inputs & 4 current inputs All-terrain shockproof casing resistant to UV light and high temperatures Ideal for mounting on electricity poles Self-powered by its voltage inputs up to 1,000 V Continuous recording at 200 ms intervals Measurements in compliance with IEEE 1459 Inputs  5 Voltage / 4 Current Sample Rate 128 per Cycle 6.4kHz at 50Hz 7.68kHz at 60Hz Specification Range Measurement Range Resolution Accuracy (Typical) Volt Vrms 1000V P to N 10 to 1000V 0.1V ±0.2% Rdg +0.2V Vrms 1000V E to N 10 to 1000V 0.1V ±0.2% Rdg +0.2V Urms 1000V P to P 17 to 1000V 0.1V ±0.2% Rdg + 0.4V Amps @ 50 and 60Hz Amps (1V nominal)(excluding clamp accuracy Probe dependent 0.2%< I < 120% Inom Probe dependent ±0.2% Rdg + 0.02% Inom AmpFLEX & MiniFlex (including sensor accuracy) Range 100A Range 400ARange 2kARange 10kA 200mA to 120A5 to 440A50 to 2400A400A to 12kA 1mA0.1A0.1A & 1A1A ±1.2% Rdg + 50mA±1.2% Rdg + 0.2A±1.2% Rdg + 1A±1.2% Rdg + 5A Frequency   42.5 to 69Hz 0.01Hz ±0.1Hz Power Watts (VA, var) P-Q-S 20W to 20GW / 20var to 10Gvar / 20VA to 10GVA 4 digits min ±0.5% Rdg + 0.005% Pnom Power Factor (Cos Φ/DPF) -1  to 1 0.001 ±0.05 Energy kWh (kVAh, kvarh) P-Q-S Up to 4EWh / 4Evarh / 4 EVAh (E = 1018 ) ±0.5% Rdg Harmonics DC, 1 to 50 Volts & Amp %   0.01 to 655.0% 0.01% ±1% Rdg from 1 to 25 THD   0.00 to 655.0% 0.01% ±1% Rdg General Features Case Design Rugged field case Interface Isolated USB, Bluetooth, and Ethernet, Wi-Fi, SD card for direct transfer to PC. Dataview software for real time data, configuration and reporting included Memory 8GB SD card (SDHC compliant, FAT32 formatted)  32GB max Display LCD with backlight 4.2 x 3.3” (107 x 84mm) Real-Time Clock Time and date stamp for Trend mode Power Phase to phase or phase to neutral 100 to 1000VAC or external power pack 110V/230V 50/60Hz 15VA; Battery backup when power OFF, 60 minutes typical Dimensions (L x W x H) 9.65  x 10.6 x 7.1” (245 x 270 x 180mm) Weight 8.9 lbs (4kg) Altitude Operating 2000m (6560ft) Operating Temperature 32° to 108.5°F; (0° to +42.5°C) from 10 to 85% RH Storage Temperature -4° to 122°F; (-20° to +50°C) from 0 to 75% RH with battery pack Electro-Magnetic-Compatibility (EMC) EN 61326-1 for emission and immunity IP Rating IP 67 per IEC 60529 Safety IEC/EN 61010-1 (1000V CAT IV Pol 4) Download Specifications : Click Here

Product Description Pyrocontrole is strengthening its offering of video recorders with its new-generation PYROtracer C.A 6500 with touch screens. This new range of three paperless recorders  (C.A 6510, C.A 6520, C.A 6530) benefits from the very latest technological developments: Faster recording rate Improved data security Customized configuration Intuitive operation Multiple recording channels Access to the data on site and/or remotely All these advantages help to optimize your results in the field! Secure data logging on up to 144 channels These three recorders, from the standard model standard to the most powerful, cover every requirement, whatever the budget. Depending on the model, the recording capabilities may extend up to 144 channels with an acquisition interval of 100 ms per channel, ideal even for the most demanding applications. Customizable graphic recorders For fully-intuitive handling, these recorders are configurable and therefore adaptable to match each customer's industrial environment. With the Panel STUDIO software, users can create their own applications. The screens customized in this way allow you to monitor all or part of the installation on the recorder. Master communication Configurable as simple stand-alone units for unique data acquisition applications, these C.A 6500 recorders can also be set up in Master communication mode for supervising an entire installation. This configuration enables users to take full advantage of the recorder's performance features (secure data storage, supervision on a touch screen, remote viewing of the data, etc.). Compact design Particularly compact with a depth of just 170 mm, the C.A 6500 models are easy to flush-mount in a cabinet. Depending on the applications, a portable version with a handle is also available which is easy to carry around, both in workshops and on outdoor sites. Advantages Easy-to-read, intuitive interface > LED touch screen which can be customized for optimum display and easy reading Multiple possibilities > 3 to144 recording channels Secure & fast > Secure data > 100 ms acquisition interval per channel > Multilingual: 19 languages Open and communicating > Ethernet as a standard feature > Modbus master, web server Advanced functions > Pulse-counting input > Math & Logic functions > Batch management > FDA 21 CFR part11 > Customizable screens > Multilingual, 19 languages Compact, rugged design > IP65 and reduced depth of casing

Description: FHO5000 series Optical Time Domain Reflectometer (OTDR) is an intelligent meter of a new generation for the detection of fiber communications systems. With the popularization of optical network construction in cities and countrysides, the measurement of optical network becomes short and disperse; FHO5000 is specially designed for that kind of application. It’s economic, having outstanding performance. FHO5000 is manufactured with patience and carefulness, following the national standards to combine the rich experience and modern technology, subject to stringent mechanical, electronic and optical testing and quality assurance; in the other way, the new design makes FHO5000 more smart and compact and multi-purpose. Whether you want to detect link layer in the construction and installation of optical network or proceed efficient maintenance and trouble shooting, FHO5000 can be your best assistant. Grandway FHO5000 OTDR CATALOG FEATURES Integrated design, smart and rugged IP65 protection level, outdoor enhanced 7-inch anti-reflection LCD screen PON online test module (1625nm) is optional MMF test module (850/1300nm) is optional Support multi-language display and input APPLICATIONS FTTX test with PON networks CATV network testing Access network testing  LAN network testing Metro network testing  Lab and Factory testing Live fiber troubleshooting Ready for all kinds of environment. FHO5000 series OTDR is specially designed for tough outdoor jobs. IP65 protection level, lightweight, easy operation, low-reflection LCD and more than 12 hours working period make it perfect in field testing. Meanwhile, optional PCB board with water-proof coating helps FHO5000 series OTDR get better protection performance.  What you need is all-in-one! FHO5000 series OTDR is a highly integrated platform that features with four module slots, with a large 7-inch color screen (with a touchscreen option), a high-capacity Lithium-Ion battery, an optional microscope (through universal serial bus [USB] port), and built-in optical test functions, such as PON test module, visual fault locator (VFL), optional power meter and laser source, making it qualified in the installation, turn-up, and maintenance of FTTx/Access optical networks. Structure Humanized Test Interface FHO5000 series OTDR could display Splice loss, Connector loss, Fiber attenuation, Reflection of points, Link opitcal return loss and distance to fiber events etc. With test information in a smart way, user could get detailed information immediately. Quick fit in short time Simplified display style and structured menus help effective in reducing the time of study. FTTH test within PON networks FHO5000 series OTDR’s models, like T40F and T43F, are dedicated to the testing of PON network maintenance and troubleshooting without service disruption. Last mile master FHO5000 series OTDR could easily test through 1*32 PLC splitter in PON test (Model: FHO5000-T43F). Fiber Microscope Microscope is optional for FHO5000 series OTDR. 400X amplification and variety of accessories ensure perfect terminal condition before test. The essential first step Taking time to properly inspect connector end faces can prevent a slew of problems down the lines, saving you time, money and headaches. Result transfer Check test results on PC or PDA through USB; 4GB large internal memory space could store more than 40,000 groups of results. Link in line Download reference traces and settings from database Send measurement results via email Ask for remote help Data Manager Use Data Manager to elaborate and print out result files on upper computer within a few steps. High Compatibility Support:     -Windows Vista (32/64 bit system)     -Windows 7 (32/64 bit system)     -Windows 8 (32/64 bit system)     -Microsoft Office Excel 2007     -Microsoft Office Excel 2010     -Microsoft Office Excel 2013 Delicate Report     -Simplified display style easy to read, support multi-result printing. SpecificationGeneral Dimension  253×168×73.6mm 1.5kg (battery included) Display 7 inch TFT-LCD with LED backlight (touch screen function is optional) Interface 1×RJ45 port, 3×USB port (USB 2.0, Type A USB×2, Type B USB×1) Power Supply 10V(dc), 100V(ac) to 240V(ac), 50~60Hz Battery 7.4V(dc)/4.4Ah lithium battery (with air traffic certification) Operating time: 12 hours①, Telcordia GR-196-CORE Charging time: <4 hours (power off) Power Saving Backlight off: Disable/1 to 99 minutes Auto shutdown: Disable/1 to 99 minutes Data Storage Internal memory: 4GB (about 40,000 groups of curves) Language User selectable (English, Simplified Chinese, traditional Chinese, French, Korean, Russian, Spanish and Portuguese-contact us for availability of others) Environmental Conditions Operating temperature and humidity: -10℃~+50℃, ≤95% (non-condensation) Storage temperature and humidity: -20℃~+75℃, ≤95% (non-condensation) Proof: IP65 (IEC60529) Accessories Standard: Main unit, power adapter, Lithium battery, FC adapter, USB cord, User guide, CD disk, carrying case Optional: SC/ST/LC adapter, Bare fiber adapter Technical parameter Type② Testing Wavelength  (MM: ±20nm, SM: ±10nm) Dynamic Range (dB)③ Event/Attenuation Dead-zone (m)④ FHO5000-M21 850/1300 19/21 0.8/4 FHO5000-MD21 850/1300 1310/1550 19/21 35/33 0.8/4 1/4 FHO5000-MD22 850/1300 1310/1550 19/21 40/38 0.8/4 1/4 FHO5000-D26 1310/1550 26/24 0.8/4 FHO5000-D32 1310/1550 32/30 0.8/4 FHO5000-D35 1310/1550 35/33 0.8/4 FHO5000-D40 1310/1550 40/38 1/4 FHO5000-D43 1310/1550 43/41 1/5 FHO5000-D45 1310/1550 45/43 1/5 FHO5000-T40F 1310/1550/1625 40/38/38 1/4 FHO5000-T43F 1310/1550/1625 43/41/41 1/5 FHO5000-T45F 1310/1550/1625 45/43/43 1/5 FHO5000-TC35F 1310/1550/1650 35/33/31 0.8/4 FHO5000-TP35 1310/1490/1550 35/33/33 0.8/4 Test parameter Pulse Width Single mode: 3ns, 5ns, 10ns, 20ns, 50ns, 100ns, 200ns, 500ns, 1μs, 2μs, 5μs, 10μs, 20μs Multi-mode: 3ns, 5ns, 10ns, 20ns, 50ns, 100ns, 200ns, 500ns, 1μs, 2μs Testing Distance Single mode: 100m, 500m, 2km, 5km, 10km, 20km, 40km, 80km, 120km, 160km, 240km Multi-mode: 500m, 2km, 5km, 10km, 20km, 40km Sampling Resolution  Minimum 5cm Sampling Point Maximum 128,000 points Linearity  ≤0.05dB/dB scale Indication X axis: 4m~70m/div, Y axis: Minimum 0.09dB/div Distance Resolution 0.01m Distance Accuracy  ±(1m+measuring distance×3×10-5+sampling resolution) (excluding IOR uncertainty) Reflectance Accuracy Single mode: ±2dB, multi-mode: ±4dB IOR Setting 1.4000~1.7000, 0.0001 step Units Km, miles, feet OTDR Trace Format Telcordia universal, SOR, issue 2 (SR-4731) OTDR: User selectable automatic or manual set-up Testing Modes Visual fault locator: Visible red light for fiber identification and troubleshooting Light source: Stabilized Light Source (CW, 270Hz, 1kHz, 2kHz output) Field microscope probe Fiber Event Analysis -Reflective and non-reflective events: 0.01 to 1.99dB (0.01dB steps) -Reflective: 0.01 to 32dB (0.01dB steps) -Fiber end/break: 3 to 20dB (1dB steps) Other Functions Real time sweep: 1Hz Averaging modes: Timed (1 to 3600 sec.) Live Fiber detect: Verifies presence communication light in optical fiber Trace overlay and comparison VFL Module (Visual Fault Locator, as standard function): Wavelength (±20nm) 650nm Power  10mw,CLASSIII B Range 12km Connector FC/UPC Launching Mode CW/2Hz PM Module (Power Meter, as optional function): Wavelength Range (±20nm) 800~1700nm Calibrated Wavelength 850/1300/1310/1490/1550/1625/1650nm Test Range Type A: -65~+5dBm (standard); Type B: -40~+23dBm (optional) Resolution 0.01dB Accuracy ±0.35dB±1nW Modulation Identification 270/1k/2kHz,Pinput≥-40dBm Connector FC/UPC LS Module (Laser Source, as optional function): Working Wavelength (±20nm) 1310/1550/1625nm⑤ Output Power  Adjustable -25~0dBm Accuracy ±0.5dB Connector FC/UPC FM Module (Fiber Microscope, as optional function): Magnification 400X Resolution 1.0µm View of Field 0.40×0.31mm Storage/working Condition -18℃~35℃ Dimension 235×95×30mm Sensor 1/3 inch 2 million of pixel Weight 150g USB 1.1/2.0 Adapter⑥   SC-PC-F (For SC/PC adapter) FC-PC-F (For FC/PC adapter) LC-PC-F (For LC/PC adapter) 2.5PC-M (For 2.5mm connector, SC/PC, FC/PC, ST/PC) Notes: ①Typical, backlight off, sweeping halted at 25℃, 12 hours typical continuous testing. ② Model T40F/T43F/T45F are integrated with optical filter, which allow them to test PON network online (by using 1625nm wavelength) and will not interrupt the fiber signal. ③Dynamic range is measured with maximum pulse width, averaging time is 3 minutes, SNR=1; The level difference between the RMS noise level and the level where near end back-scattering occurs. ④Event dead zone is measured with pulse width of 3ns; attenuation dead zone is measured with pulse width of 5ns. ⑤1310/1550nm laser source uses OTDR1 port, and 1625nm or 850/1300nm uses OTDR2 port. ⑥For more adapters, please contact us. Ordering Information

Product Overview SIGLENT’s SDS2000X Series Super Phosphor Oscilloscopes are available in bandwidths of 70 MHz, 100 MHz, 200 MHz and 300 MHz, maximum sample rate of 2 GSa/s, and come with a maximum record length of 140 Mpts. The most commonly used functions can be accessed with its user-friendly one-button design. The SDS2000X series employs a new generation of SPO technology. It has an innovative digital trigger system with high sensitivity and low jitter, and a maximum waveform capture rate of 140,000 wfm/s (normal mode), up to 500,000 wfm/s (sequence mode). It also employs the common 256-level intensity grading display function but also a color temperature display mode. The trigger system supports multiple powerful triggering modes including serial bus triggering, History waveform recording and sequence acquisition allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a built-in 25 MHz arbitrary waveform generator, 16 digital channels (MSO), as well as serial decoding are also features of the SDS2000X. Key Features ◆ 70 MHz, 100 MHz, 200 MHz, 300 MHz models ◆ Real-time sampling rate up to 2 GSa/s  • Waveform capture rate up to 140,000 wfm/s (normal mode), and 500,000 wfm/s (sequence mode)  • Supports 256-level intensity grading and color temperature display  • Record length up to 140 Mpts  • Digital trigger system ◆ Intelligent trigger: Edge, Slope, Pulse, Window, Runt, Interval, Dropout, Pattern and Video (HDTV supported) ◆ Serial bus triggering and decoder, supports protocols IIC, SPI, UART, RS232, CAN and LIN (Optional) ◆ Low background noise, supports 1 mV/div to 10 V/div voltage scales ◆ 10 types of one-button shortcuts, including Auto Setup, Default, Cursors, Measure, Roll, History, Display/Persist,     Clear Sweeps, Zoom and Print ◆ Segmented acquisition (Sequence) mode divides the maximum record length into multiple segments (up to 80,000),     according to trigger conditions set by the user. The resulting acquisition has a very small dead time segment. ◆ History waveform record (History) function, the maximumr ecorded waveform length is 80,000 frames ◆ Automatic measurement function on 37 parameters, supports statistics, Gating measurements, Math measurements,     History measurements and Ref measurements ◆ Math function (FFT, addition, subtraction, multiplication, division, integration, differential, square root) ◆ High Speed hardware based Pass/ Fail function ◆ 16 Digital channels (MSO option), Maximum waveform capture rate up to 500 MSa/s, Record length up to 140 Mpt/CH ◆ 25 MHz function/arbitrary waveform generator, built-in 10 types of waveforms (option) ◆ Large 8 inch TFT-LCD display with 800 * 480 resolution ◆ Multiple interfaces: USB Host, USB Device (USBTMC), LAN (VXI-11), Pass/Fail, Trigger Out ◆ Supports SCPI remote control commands ◆ Supports Multi-language display and embedded online Help Ordering Information Product Name Product Description SDS2304X 300 MHz, 4 CH, 2 GSa/s (Max.), 140 Mpts SDS2302X 300 MHz, 2 CH, 2 GSa/s (Max.), 140 Mpts SDS2204X 200 MHz, 4 CH, 2 GSa/s (Max.), 140 Mpts SDS2202X 200 MHz, 2 CH, 2 GSa/s (Max.), 140 Mpts SDS2104X 100 MHz, 4 CH, 2 GSa/s (Max.), 140 Mpts SDS2102X 100 MHz, 2 CH, 2 GSa/s (Max.), 140 Mpts SDS2074X 70 MHz, 4 CH, 2 GSa/s (Max.), 140 Mpts SDS2072X 70 MHz, 2 CH, 2 GSa/s (Max.), 140 Mpts Standard Accessories USB Cable -1 Passive Probe -4 Power Cord -1 Quick Start -1 Certification -1 Certificate of Calibration -1 CD (Including User Manual and EasyScopeX software) -1 Optional Accessories SDS-2000X-DC IIC, SPI, UART/RS232, CAN, LIN Decoder SDS-2000X-FG 25MHz Function/Arbitrary Waveform Generator SDS-2000X-PA Power Analyze Software SDS-2000X-16LA 16 Digital Channels（Software） SPL2016 16 Channel Logic Probe ISFE Isolated Front End STB STB Demo Source DF2001A Power analysis Deskew Fixture HPB4010 High Voltage Probe Current Probe Current Probe: CP4020/CP4050/CP4070/ CP4070A/CP5030/ CP5030A/CP5150/CP5500 High Voltage Differential Probe High Voltage Differential Probe: DPB4080/DPB5150/ DPB5150A/DPB5700/ DPB5700A

Description The C.A 5275 multimeter is equipped with a double 6,000-count backlit display and a 61+2-segment bargraph with remanent effect. Its 600V CAT IV safety is backed by IP54 ingress protection. Its very wide measurement ranges allow measurements up to 1,000 V, 10 A, 60 MΩ and 60 mF with resolutions of 10 μV, 1 μA, 100 mΩ and 1 pF. Designed and manufactured in France by CHAUVIN ARNOUX, this multimeter comes with a 3-year warranty. TRMS AC+DC measurement of voltage and current 12-bit converter 5 measurements / second CAT IV 600V / CAT III 1,000V IP54 Double 6,000-count backlit display and 61+2-segment bargraph Automatic or manual range selection VLowZ low-impedance voltage measurement with low-pass filter 1,000 V / 10 A 10 µV resolution Current from 1 µA Measurement of ionization currents Min / Max measurements Resistance / audible continuity Capacitance 3-year warranty  Equivalent to APPA 98III / Fluke 177 & 175

Description With its compact design and built-in test probes, you can take the C.A 702 with you everywhere you go. AC and DC voltages: 200 mV to 600 V Resistance: 200 OHM to 20 MOHM Continuity test (buzzer) and diode test Safety: IEC 61010 - 600V CAT IV / 1000V CAT III  

Advantages Large LCD for multi-parameter display on 70x52 mm backlit screen. Analytical tools: time/date-stamped surveillance of relative, Peak+/-  and secondary measurements for an easy-to use multimeter with its digital keyboard equipped with lighting. Optimized ergonomics: IP67 leakproof casing, IEC61010 1,000V CAT III/600V CAT IV safety measurement terminals, power supply by normal battery or Ni-MH rechargeable battery with comprehensive management of the battery charge on screen. Multiple quantities measured around the main function, relative measurements and direct measurement of current via a clamp (mV output) with integration of the transformation ratio for an advanced multimeter.USB communication via the SX-DMM software delivered with the product and SCPI programming commands. Description ASYC IV MTX 3291 - The reference for multimetersThese portable multimeters with digital display allowing direct measurement of the main electrical quantities benefit from an innovative design making them compact, rugged, leakproof and comfortable to grip.Simple multimeters• Easy-to-read 70x52 mm LCD screen• Contextual reminder of connection on the screen• Current autoranging, single terminal up to 10 A• Secondary measurements in addition to the main measurement to facilitate analysis• Surveillance of the MIN/MAX and AVG data with relative time/date-stamping and of voltage and current peaks• SX-DMM software for real-time processing of the data on a PCAnd much more...• IP67 protection against water projection and dust, ideal for outdoor conditions• Powered by 4 standard AA batteries or 4 Ni-MH batteries rechargeable with an HX0051B external module (option)• Operation for up to 400 hrs on batteries

Advantages Large LCD for multi-parameter display on 70x52 mm screen. A simple basic multimeter with surveillance of the main functions: Min, Max, Avg and Peak+/- . Digital keyboard with lighting. Optimized ergonomics: IP67 leakproof casing, IEC61010 600V CAT III/300V CAT IV safety measurement terminals, power supply by normal battery or Ni-MH rechargeable battery (external charger) and contextual reminder of connections on screen. Description ASYC IV MTX 3290 - The reference for multimeters These portable multimeters with digital display allowing direct measurement of the main electrical quantities benefit from an innovative design making them compact, rugged, leakproof and comfortable to grip.Simple multimeters• Easy-to-read 70x52 mm LCD screen• Contextual reminder of connection on the screen• Current autoranging, single terminal up to 10 A• Secondary measurements in addition to the main measurement to facilitate analysis• Surveillance of the MIN/MAX and AVG data with relative time/date-stamping and of voltage and current peaksAnd much more...• IP67 protection against water projection and dust,ideal for outdoor conditions• Powered by 4 standard AA batteries or 4 Ni-MH batteries rechargeable with an HX0051B external module (option)• Operation for up to 400 hrs on batteries

Description The MX 24 is the 5,000/50,000-count TRMS digital multimeter of reference in the MXCONCEPT range. Equipped with an ADP input, it can be connected to a variety of accessory probes: luxmeter, current clamp, thermometer, etc.   • Backlighting, 34-segment bargraph   • VlowZ 500 kΩ low-impedance measurement input   • Voltage up to 1,000 VDC and 750 VAC, impedance 10 MΩ   • Direct current measurement up to 50 mA and 10 A AC/DC (20 A 30 s) •  Resistance up to 50 MΩ •  Audible continuity test, diode test • Capacitance meter function from 50 nF to 50 mF • Frequency meter function up to 500 kHz • MEM/AUTOMEM key • Dimensions 170x80x35 mm, weight 300 g. • Warranty: 3 years • Safety: IEC 61010-1 Cat.III 600 V  

Product Description The PEL 103 is a low cost, simple to use, one, two (split phase) and three phase power/energy data logger. This product is ideal for electricians, engineers and contractors doing work in the area of building and system monitoring and upgrades, as well as residential and overall energy audits. All vital energy data is easily measured, recorded, and analyzed. Reports can be generated with confidence with minimal configuration time and effort (Standard and Customizable Reports supplied). The instrument’s design enables it to be installed inside a load center panel (including the current sensors) allowing the door to close on most panels. The PEL 100 series offers all the essential functions for logging power/energy data from most electrical power networks in use today across the world (17 network set-ups provided). The PEL 100 series energy loggers measure and record three True RMS voltage inputs and current inputs, Watts, VARS, VA and Energy (kWh and kVA). Power Factor (PF), Displacement Power Factor (DPF), Crest Factor, Frequency and THD are calculated and recorded as well. Individual harmonic % information from 1 to the 50th harmonic are recorded at the operator’s choice. All variables are recorded and stored at a one second interval and on user selectable demand intervals from 1 to 60 minutes. The PEL 103 comes either with or without sensors, see model options and descriptions below. Ergonomic, magnetized and suitable for all types of cabinets, PEL103 loggers provide all the power and energy measurements simultaneously. Single-phase, split-phase and three-phase installations with or without a neutral, as well as other complex configurations. Implementation without cutting off the mains power supply BlueTooth, Ethernet and USB communication Automatic recognition of the sensors connected Recording on SD and SD-HC cards Real-time communication with a PC and analysis using PEL Transfer software Other specifications: Voltage up to 1,000 V Current up to 10,000 A Voltage ratio / current ratio up to 650,000 V / up to 25,000 A Power from 10 W/var/VA to 10 GW/Gvar/GVA Energy up to 4EWh / 4 EVAh / 4 Evarh Phase: cos φ, tan Φ, PF Harmonics up to 50th order 2 GB SD memory card (SD-HC card up to 32 GB) Specifications Inputs  3 Voltage / 3 Current: calculation of neutral current Sample Rate 128 per Cycle 6.4kHz at 50Hz 7.68kHz at 60Hz Specification Range Measurement Range Resolution Accuracy (Typical) Volt Vrms 1000V P to N 10 to 1000V 0.1V ±0.2% Rdg + 0.2V Urms 1000V P to P 17 to 1700V 0.1V ±0.2% Rdg + 0.4V Amps @ 50 and 60Hz Amps (1V nominal)(excluding clamp accuracy Probe dependent 0.2%< I < 120% Inom Probe dependent ±0.2% Rdg + 0.02% Inom AmpFLEX & MiniFlex (including sensor accuracy) Range 100A Range 400ARange 2kARange 10kA 200mA to 120A5 to 440A50 to 2400A400A to 12kA 1mA0.1A0.1A & 1A1A ±1.2% Rdg + 50mA±1.2% Rdg + 0.2A±1.2% Rdg + 1A±1.2% Rdg + 5A Frequency   42.5 to 69Hz 0.01Hz ±0.1Hz Power Watts (VA, var) P-Q-S 10W to 10GW / 10var to 10Gvar / 10VA to 10GVA 4 digits min ±0.5% Rdg + 0.005% Pnom Power Factor (Cos Φ/DPF) -1  to 1 0.001 ±0.05 Energy kWh (kVAh, kvarh) P-Q-S Up to 4EWh / 4Evarh / 4 EVAh (E = 1018 ) ±0.5% Rdg Harmonics DC, 1 to 50 Volts & Amp %   0.01 to 655.0% 0.01% ±1% Rdg from 1 to 25 THD   0.00 to 655.0% 0.01% ±1% Rdg General Features Case Design Rugged, shock proof with integrated protective holster, IP54 not included terminals. Shock and vibration IEC61010 Interface Isolated USB, Bluetooth, and Ethernet, SD card for direct transfer to PC. Dataview software for real time data, configuration and reporting included Memory 8GB SD card (SDHC compliant, FAT32 formatted)  32GB max Display LCD with backlight Real-Time Clock Time and date stamp for Trend mode Power AC 110V/230V 50/60Hz 15VA; Battery backup when power OFF, 60 minutes typical Dimensions (L x W x H) 10.08 x 4.92 x 1.46” (256 x 125 x 37mm) Weight 2.2lbs (1kg) Altitude Operating 2000m (6560ft) Operating Temperature 32 to 108.5°F; (0°C to +42.5°C) from 10 to 85% RH Storage Temperature -4 to 122°F; (-20°C to +50°C) from 0 to 75% RH with battery pack Electro-Magnetic-Compatibility (EMC) EN 61326-1 for emission and immunity IP Rating IP54 per IEC 60529 Safety IEC/EN 61010-1 (1000V CAT III-600V CAT IV), IEC 1326-1 Download Specifications : Click Here

VDV II Voice, Data Video Testers Product Overview The new VDV II Series are easy to use cable verification testers that check the integrity of copper cables commonly found in domestic, commercial or industrial voice, data or video installations, including telephone wiring, data network and video/security cabling. Accurate - Advanced TDR (Time Domain Reflectometry) measures cable length and provides distance to fault information in the VDV Pro Fast - Identifies wiring errors instantly and displays the results all on one screen Intelligent - Quickly determines which phone service is running over cables, such as ISDN or PBX. Identifies voltage, pin and polarity for PoE (Power Over Ethernet) applications. Features  Three completely new tester models: VDV II Pro, VDV II Plus and VDV II for applications that require a range of verification testing from accurate and advanced wiremapping to verifying PoE presence, Ethernet Detection, and Phone service detection. Three new accessory packs for use with all of the new VDV II Testers. RJ-45 Remotes for wiremapping and identifying 12 individual cables. Coax F remotes for wiremapping and identifying 12 individual coaxial cables. RJ-45 identifiers for identifying locations of up to 24 RJ-45 outlets or panel ports. VDV II Offers all standard copper testing including: Coax, 6Pin (RJ-11/12), 8Pin (RJ-45) Input Connectors for Copper Cable Testing Wiremap for Miswires, Split Pairs, Shorts and Opens. Identifies crossover/uplink cables. Analog Tone Generator – 4 selectable tones. Tone by pin, by pair, or by all conductors. Voltage Protection. Unit alerts user to errant/unidentified voltage and prevents damage to tester. Tests Cat 3, Cat 5e, Cat 6, Cat 6A, Cat 7 and STP (shielded) cables. Single Screen Results. All cable tests performed at once with immediate results. 2.7” clear, easy to read display. VDV II Plus All the features of the VDV II including: Larger 2.9" Display Backlight with user selectable timeouts Hub Blink to identify port connectivity Overall, and by pair, cable length measurement including distance to opens to aid in troubleshooting Carrying Case, Adapters & Cables VDV II Pro All the features of the VDV II, VDV II Plus and... TDR measurement to identify distance to opens and shorts for accurate and advanced troubleshooting. PoE Detection with Voltage, Pin, and Polarity Information Phone Service Detection: PBX / ISDN Ethernet Detection with Network Rate & Duplex Information. Identifies 10/100/1000Mb and Hd/Fd on connected ports/devices. Both the VDV II Plus and the VDV II Pro include a carrying case that can hold all optional VDV II accessories plus an optional Tone Probe (62-164). Included in the carrying case are: 2 RJ-45 to alligator clip cable assemblies 2 RJ-45 patch cables 2 RJ-11 patch cables 1 Coax F patch cable 1 F-81 barrel splice 1 BNC female to F male adapter 1 BNC female to F female adapter 1 RCA female to F male adapter 1 RCA female to F female adapter

SignalTEK II FO Cable and Network Transmission Tester Product Overview  Meet our Handheld qualifier designed to confirm correct installation of copper and fiber cabling capable of supporting voice, video, data and CCTV applications over 10/100 Megabit or Gigabit Ethernet. SignalTEK® II is essential for all installers of data cabling whether working in residential premises, small to medium-sized offices, or industrial Ethernet environments. Features Full Gigabit bi-directional load testing Save time and improve the reliability of your test results with full bi-directional testing Additional Ethernet troubleshooting capabilities Maximize Return on Investment with the added ability to identify Ethernet, Power over Ethernet (PoE) and PoE+ issues, in addition to verifying Ethernet connectivity Suitable for both copper and fiber Eliminate the need to purchase and carry multiple different testers by using one device to conduct active and passive testing across both copper and fiber networks Wiremapping by pin as well as pair Save time on the job and locate wiremap faults more quickly and accurately by testing via both pin and pair, detecting split pairs and identifying the distance to fault Reporting of test results Simplify customer reporting and create accurate documentation on jobs undertaken using SignalTEK® II to generate and store test results in standards compliant XML format. Additionally, view and export results to enable report printing Load test through hubs and switches Save money by measuring available network speed without needing to purchase a separate transmission tester SignalTEK® II FO - Operates on both copper and fiber optic networks SignalTEK® II FO 1 x Near-End unit (copper and fiber), 1 x Remote unit (copper and fiber), 2 x Power module (rechargeable), 2 x Mains PSU/charger, 2 x 30cm RJ45 cable, 1 x Quick reference guide (English), 1 x User manual CD, 1 x Carrying case. Fiber optic SFP modules not included.

NaviTEK II PRO R151002 Product description IDEAL INDUSTRIES NETWORKS range of hand held test devices offer a comprehensive range of active and passive network test capability from basic cabling faults through to network monitoring, PC diagnostics and VoIP QoS amongst many others. This range delivers easy to use, high performance test and troubleshooting capability in LAN, WLAN and VLAN networks over copper, fibre and WiFi ensuring minimum downtime and saving money. NaviTEK II Meet our versatile networks technician's tester for troubleshooting and maintenance of active and passive networks across both copper and fibre, helping to pinpoint and solve networking issues quickly. As a powerful LAN management tester for installers and IT or facilities maintenance professionals working in any enterprise, residential, campus or industrial Ethernet environment, NaviTEK II saves money and increases efficiency by simplifying and accelerating network troubleshooting using a single multifunction device. Features  Suitable for copper and fibreEliminate the need to purchase and carry multiple different testers by using one device to conduct active and passive testing across both copper and fibre networks Wiremapping by pin as well as pairSave time on the job and locate wiremap faults more quickly and accurately by testing via both pin and pair, detecting split pairs and identifying the distance to fault Additional Ethernet troubleshooting capabilitiesMaximise Return on Investment with the added ability to identify Ethernet and Power over Ethernet (PoE) issues, in addition to verifying Ethernet connectivity Support for IPv6 and PoENaviTEK II supports both IPv4 and IPv6 internet addresses, as well as PoE, making it a future-proof investment Reporting of test resultsSimplify customer reporting and create accurate documentation on jobs undertaken using NaviTEK II to generate and store test results in standards compliant XML format. Additionally, view and export results to enable report printing 802.1x compatibilityLog onto networks secured by this protocol, avoiding unnecessary security complications and lengthy project delays   https://www.youtube.com/watch?v=cOqqH7cRQeQ&feature=youtu.be NaviTEK II is available in three models with specifications to meet all user needs   NaviTEK II Entry model facilitates LAN testing over copper networks and includes functionality for detecting PoE Part No. Kit Contents R153000: NaviTEK II 1 x NaviTEK II test unit, 1 x Remote unit No. 1, 4 x AA dry cell batteries (non-rechargeable), 2 x Patch cables - 30cm, Cat. 5e STP,1 x Manual on CD, 1 x Quick reference guide, 1 x Carrying case   NaviTEK II PLUS Introduces additional testing capabilities, including support for VLAN and sto­rage for test results Part No. Kit Contents R151000: NaviTEK II PLUS 1 x NaviTEK II PLUS test unit, 1 x Remote unit No. 1, 2 x Patch cables - 30cm, Cat. 5e STP, 1 x Rechargeable power module, 1 x PSU with UK/EU/US adaptors, 1 x Manual on CD, 1 x Quick reference guide, 1 x Carrying case NaviTEK II PRO Fully featured solution, suitable for copper and fibre networks Part No. Kit Contents R151002: NaviTEK II PRO – Premium kit 1 x NaviTEK II PRO test unit, 1 x Remote unit No. 1, 2 x Patch cables - 30cm, Cat. 5e STP, 1 x Rechargeable power module, 1 x PSU with UK/EU/US adaptors, 1 x Manual on CD, 1 x Quick reference guide, 1 x Carrying case

Model    TO102  TO104  TO102A  TO104A  TO152  TO154    TO152A   TO154A TO202 TO204 TO202A TO204A Bandwidth 100MHz 100MHz 150MHz 150MHz 200MHz 200MHz Risetime <=3.5ns <=3.5ns <=2.3ns <=2.3ns <=1.75ns <=1.75ns Real time sampling rate 1GSa/s 2GSa/s 1GSa/s 2GSa/s 1GSa/s 2GSa/s Memory depth 18Mpts 90Mpts 18Mpts 90Mpts 18Mpts 90Mpts Waveform capture rate 250,000wfm/s 500,000wfm/s 250,000wfm/s 500,000wfm/s 250,000wfm/s 500,000wfm/s Channels       2/4 Display screen     10.1"TFT LED Multi point touchalble capacitive screen,Resolution：1024*600 Operation      Mouse,Multi-touch:tap,swipe,pinch Time base range     2ns/div to 1000s/div for TO***model, 1ns/div to 1000s/div for TO***A model Vertical resolution      8bit Vertical Scale      2mV/div to 5V/div Triggger types     Edge,Pulse,Logic Automatic measurements     Period, Frequency, Risetime, Falltime, Delay, PDC, NDC, PPW, NPW, BPW, POS, NOS, Phase, PKPK, Amp., Height, Low, Max, Min, RMS,      CRMS, Mean, CMean Math operation      +,-,*,/,FFT FFT window function      Rectangular, Hamming, Hanning, Blackman I/o port      USB Host, USB Device Built-in storage      4G Dimensions and weight      275mm*210mm*60mm，1770g   Standard Accessories   Item Description USB Cable Connect scope with PC Probe Standard passive, bandwidth and quantity depend on model Power adapter For charging USB calibration connect board Probe compensation Documents Product Quick Guide, Safety Information,Packing List, Calibration Certificate, Quick Start    

MobIR M8 Unique Mobile-like IR Thermographic Camera   Product Description The MobIR M8 represents a landmark of Infrared technology progress globally. It is the latest innovation from Guide Infrared who always work with innovative ideas. Guide Infrared presents the M8, extending the features exclusively for the  high-end Infrared camera which has never been done before. With a impressive 50Hz refresh rate, 2Mpixels CMOS, Touch screen, Auto focus, IR video recording, whatever you expect from a thermal camera, the M8 satisfies your needs by its compactness, ruggedness, accuracy, efficiency, reliability and affordability.   MobIR M8 Thermal Camera MobIR is a mobile like infrared camera. ONE  Unprecedented design of mobile like infrared camera.  Two  Exquisite outlines of double covered and open-faced  Three  Perfect technology -combinations of optics, mechanics and  electronics.   Features and Benefits   Rugged Design Magnalium housing is far more robust and shock resistant compared with other plastic ones; Intelligent built-in  lens design delivers overall protection for the optics even if you drop it on the ground by accident. The unique AGT offers double protection for the sensitive optics and detectors when it is off or in sleep mode. The optional silicon jacket offers extra protection.   Elegant Vision  With the practical and innovative design the MobIR M8 improves the traditional ideas on infrared cameras. It is a mobile like instrument, small enough to fit in the palm of your hand and is integrated with the most advanced infrared technology.   AGT- Auto Gate Technology The innovative auto gate not only functions as a shutter but also as a lens cap. Free from all disrupting heat radiation caused by the optics and electronics inside, the intelligent external shutter delivers the most crisp and uniform image presentation as well as the most stable and accurate temperature reading. At the same time, it switches off automatically in sleep mode, providing extra protection to the sensitive optics and detectors.     Unique Design allows for easy Holding and Operation  The classic mobile design makes this portable infrared camera very easy to operate. This palm sized camera, angle-adjustable LCD display enables you to reach every nook and cranny which means thermal abnormalities have got nowhere to hide.   Live Video Recording  You can record live video on the device or into  a PC via USB 2.0 which helps monitor temperature changes of the selected area, which is perfect for stationary monitoring.    Auto Capture The image can be automatically captured through the following options:  Every  15secs, 30secs, 60secs, and 5 min interval settings if necessary. With this function the camera can be mounted on a tripod for real time monitoring purposes.   Auto Focus for Both IR and Visual Image The automatic focus function is adopted in this light weight IR camera which is 160 x 120 pixels. Both clear infrared and visual images can be focused by simply pressing one button.   5 Modes of Operation The button! The Touch screen! The W/T wheel! The USB 2.0 or The infrared remote control! These 5 modes make the IR camera very fast and easy to operate.     2.0 Megapixel CMOS This portable IR camera with CMOS technology delivers high-resolution images and also allows you to make fusion images which allows for better spotting of potential problems.   IR Fusion Technology This latest Thermal Fusion technology allows you to overlay the thermal image directly on the corresponding visual image. It helps you identify exactly where the problem is.   Touch Screen The unique touch screen allows for more advanced and complicated analysis that the buttons do not allow. The touch pen allows you to highlight/outline any irregularity  that the thermal target covers, assisting you to get the most uniform and accurate measurement.   Guide Analyzer The guide free software has a friendly user interface and is compatible with Microsoft operating systems. the software allows you to store and analyze infrared images and videos. The software has many advanced functions such as image processing, thermal fusion, automatic report generation in Microsoft excel or word etc and all kinds of analyses. The muti-language availability allows the user to select the language they are most comfortable with.   4 Hours long battery time This extremely long battery time ensures the user is not interrupted  while working which means more work efficiency and they do not have to worry about the inconvenience caused by low battery power.   Applications MobIR M8 MobIR is a mobile like infrared camera • Predictive and Preventative Maintenance  • Electricity Inspections • Building Diagnostics • Technical Diagnostics • Veterinarian Helper • Helps Fight Crime       Specifications   M8 Imaging Performance Thermal Detector Type Microbolometer UFPA (160x120 pixels, 25µm) Spectral Range 8-14µm Field of View (FOV) 20.6° X 15.5° Focus Automatic and Motorized (Thermal &Visual) Thermal Sensitivity ≤80mk at 30°C Image Frequency 50HZ PAL/ 60HZ NTSC, non-interlaced Electric Zoom X2 Palette 8 Visual Built-in Digital Video CMOS Sensor, 1600x1200 pixels, 224 True Colours Image Presentation External Display 2.47" TFT LCD with high resolution Video Output PAL/NTSC IR Fusion Visual and IR blending Man-Machine Communication Touch Screen Angle Adjustable Button Yes USB 2.0 Yes W/T Wheel Yes Infrared Remote Controller Yes Measurement Temperature Range -20°C to 250°C (350°C Optional) Accuracy ±2°C or ±2% of reading Measurement Modes Auto hot & cold spot, auto alarm live/zoomed  image & video; 4 movable spots, 4 movable and changeable areas displaying either max, min or average, line profile, histogram & isotherm band  in livee/frozen/saved image Emissivity Correction Variable from 0.01 to 1.00, on-screen emissivity correction available Measurement Features Automatic correction based on distance , relative humidity, atmospheric transmission  and external optics Optics Transmission Correction Auto, based on signals from sensors Image Storage Type Removable 2GB Mini SD card & built-in memory File Format JPEG with analysis records Voice Annotation Up to 60 seconds Text Annotation Selected from preset texts or customized Automatic Image Capture Yes Live Video Recording & Measurement & Storage Recording Powerful recording up to 30 minutes in Mini SD card Measurement Automatic Max & Min temperature Storage In Mini SD card, built-in flash memory or PC Optional Accessories Telephoto Lens 30mm FOV: 7.6° x  5.7° Target Illuminator Yes Infrared Remote Controller Yes Sun Shield Yes Silicon Rubber Protecting Jacket Yes Tripod Yes Laser Locator Classification Type Class 2 semiconductor laser Power System Battery Type Rechargeable  Li-ion Camcorder battery, field-replaceable Charging System In camera or in Battery charger Battery Operating Time 4 hours continuous operation External Power Operation AC adapter 110/220VAC, 50/60Hz Environment Operating Temperature -10°C to 60°C Storage temperature -20°C to 60°C Humidity Operating and Storing 10% to 95%, non-condensing Encapsulation IP54 IEC68-2-29 Shock Operational: 25G, IEC68-2-29 Vibration Operational: 2G; IEC68-2-6 Interface USB 2.0 Real-time image, video data transfer to PC and real-time control of the camera on PC RS232 Communication Control of camera on PC Physical Characteristics Size 154mmx69mmx45mm Weight 0.35Kg (including battery) 0.27Kg (Excluding battery)       Free shipping to any address in South Africa

EasIRTM-9 is High-end infrared camera   Product Description EasIR™-9 is a high -end infrared camera of Guide EasIR series. In a rugged and ergonomical design, it is robust and shock-resistant for any tough working enviroment. The 3-button design and navigation interface allows users' skilled operation without training. Featured with Infra Fusion technology and built-in illuminator lamp, it helps you pin-point the problem exactly in high efficiency. Using EasIR™-9, easy for your work   Features and Benefits • Live Video recording • Record video on board with data and time info for review and analysis • Flexible Battery Compatibility • Never worry about battery replacement • Large Storage Capacity • Benefiting from 4G SD card inside and the capability for enlarging to a larger capacity • Large Screen Display • The 3.6 TFT LCD delivers high resolution thermal and visual image • Four Manual-focus Lens Optional • Easy satisfy users for diffrent applications with minimum invest   Specifications Thermal Detector Type Microbolometer UFPA 384×288 pixels，25μm Spectral range 8～14μm Field of View/ Focus 21.7°x16.4°/25mm,standard Optional lens 40.53°x30.96° / 13mm,13.04°x9.8°/42mm,7.85°x5.89°/70mm Thermal Sensitivity ≤0.08℃ at 30℃ Image Display 256 level,8 palettes(Rainbow,Iron,B&W,ETC) Visual Built-in digital video CMOS Sensor,1600×1200 pixels，224 true colours External Display 3.6″ TFT high resolution color LCD Temperature Range -20℃ to 250℃(400℃ , 1200 ℃ optional) Accuracy ±2℃ or ±2% of reading Measurement Modes Spot analysis Image Storage Type 4GB SD card &built-in memory (8GB SD card optional) File Format Standard JPEG with records Voice Annotation 60 seconds System Status Indication LCD Display Status of battery, indication of power Illuminator Built-in Illuminator 3 Levels adjustable Laser Locator Classification Semiconductor A1GalnP Diode Laser Power Supply Type 110/220V AC adaptor/ AA Alkaline battery Operating Time Over 2 hours continuous operation Charging System AC adapter or in external battery charger Environmental Specification Operating Temperature -10℃ to 50℃ Storage Temperature -20℃ to 60℃ Humidity Operating and storing 10% to 95%, non-condensing Encapsulation IP54 Shock Operational: 25g,IEC 68-2-29 Vibration Operational: 2g,IEC 68-2-29 Drop Test 2 meters Interface USB 2.0 Image and real-time video transfer to PC Real-time control of the camera on PC Physical Characteristics Size 182mmx112mmx252mm(with 25mm Lens) Weight 1kg(including battery, with 25mm lens) Colour Yellow&blue interlaced or red&black interlaced alternative        

Grandway FRL-02 Optical insertion Loss/Return Loss Meter Product Description: The F2H optical insertion loss/return loss meter is an integrated tester for optic fiber network, and cable manufacturer to verify the quality of fiber leads, with the features of handheld, intelligent and multi-functional. The meter is designed to be a combination of optical insertion loss tester, optical power meter, laser source and return loss tester. It is capable to not only measure return loss and proceeding the measurement of absolute and  and relative power value, but also work as a self-testing system to measure optical loss of optic fiber cable and passive device. FRL is an ideal tool to verify the polish quality of fiber, measure optical return loss in field installation, proceed routine inspection. It is no doubt to be an excellent instrument for Optic Telecom and CATV network, as well aslab test and research work. Features:  • High-precision ORL testing at 2 wavelengths (SM 1310/1550nm)  • Three instruments in one: return loss meter/power meter/insertion loss meter  • Internal data storage up to 500 records.  • Both batteries or AC power supply  • Interchangeable connectors with FC/SC/ST   Specifications:   Return loss meter Working wavelength 1310nm, 1550nm Measurement range 0~65dB Calibrated wavelengths 1310nm&1550nm Measurement accuracy 0~55dB:0.4dB; 55~65dB: 1dB Stability 0.05dB/15min Connector type FC/APC, SC/APC, ST/APC Resolution 0.1dB Data memory 1000 measurement results Power Output -2dBm   Insert loss meter Calibrated wavelengths 1310nm, 1550nm Measurement range 0~70dB Measurement accuracy 0~60dB:0.2dB; 60~70dB:1dB Data memory 500 measurement results Connector type FC/SC/ST   Power meter Calibrated wavelengths 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 625nm Measurement range -70dBm ~7dBm Measurement accuracy -70dBm ~-60dBm:1dB; -60dBm~7dBm±0..2dB~1nw Modulation detection 270HZ, 1KHZ, 2KHZ Auto-lambda detection yes Resolution 70~60dBm:0.1dB; -60~+8dBm:0.01dB Data storage 500 measurement results Connector type FC/SC/ST   Other specifications adapter INPUT:AC100~240V 50/60HZ OUTPUT: DC6V/1A USB connector Yes Battery 2*AA NI-MH 1.2V 2500mAh rechargeable Working temperature -5~+50°C Storage temperature -20~+70°C Working humidity 0~90% no condensing Support remote upgrade        

Product Description: DSA1030-PA 3GHz Spectrum Analyzer with PreAmplifier  (RIGOL) DSA1000 series products are high-performance and portable spectrum analyzers with compact design, small size and light weight. What’s more, with their low price, DSA1000 series spectrum analyzers are an ideal option to solve your budget problem. All Digital IF design 9 kHz to 2 GHz or 3 GHz Frequency Range Up to -138 dBm Displayed Average Noise Level -80 dBc/Hz @10 kHz offset Phase Noise Total Amplitude Uncertainty <1.5 dB 100 Hz Minimum Resolution Bandwidth (RBW) 3 GHz Tracking Generator (DSA1030 optional) Built-in lithium battery that can provide 3 hours continuous operation (optional) Advanced measurement functions (DSA1030 optional) and automatic settings provide ultimate flexibility 8.5 inch widescreen display with clear, vivid, and easy to use graphical interface Various interface options such as LANUSB Host, USB Device, VGA or GPIB (optional) Compact design with a weight of only 13.7 lbs    Specifications: Spectrum Analyzer Spectrum Analyzer Rigol DSA1030 Display 21.6 cm (8.5") TFT-Color-LCD with 65536 colors Resolution 800 × 480 Pixel Interfaces • USB-Host (for USB stick i.e. to save/load waveforms) • USB for a PC connection • LAN for network connection • GPIB (IEE-488, General Purpose Interface Bus) The GPIB function is only available with the use of the optional available USB GPIB module • VGA interface to connect an external display Dimensions 399 mm × 223 mm × 159 mm (15.71" × 8.78" × 6.26") Weight 6.2 kg (13.67 lbs) 7.5 kg (16.54 lbs) with connected battery. The battery is not included. Supported operation systems Windows XP(32Bit), Vista(32Bit), Windows 7(32Bit)   Function Spectrum Analyzer Rigol DSA1030 Channels 1 Frequency Range 9 kHz to 3 GHz Frequency Resolution 1 Hz Internal Frequency Reference 10 MHz Span 0 Hz (zero Span) 100 Hz to 3 GHz DANL (without preamplifier) (Displayed Average Noise level) 100 kHz to 10 MHz   10 MHz to 2,5 GHz   2,5 GHz to 3 GHz < -75dBm-3x(f/1 MHz)dB typical: -115 dBm < -117dBm-3x(f/1GHz)dB typical -120 dBm < -105dBm DANL (with preamplifier) (Displayed Average Noise level) 100 kHz to 1 MHz 1 MHz to 10 MHz   10 MHz to 2,5 GHz   2,5 GHz to 3 GHz < -93dBm < -93dBm-3x(f/1 MHz)dB typical: -133 dBm < -135dBm-3x(f/1GHz)dB typical -138 dBm < -123dBm Amplitude Range DANL to +30 dBm Max. Input Voltage 50 V Sweeptime Range 100 Hz ≤ Span ≤ 3 GHz 0 Hz (zero Span) 10 ms to 3000 s 20 µs to 3000 s Sweepmodes Normal or Single Resolution Filter 10 Hz to 1 MHz (in 1-3-10 sequence) Video Filter 1 Hz to 3 MHz (in 1-3-10 sequence) Input Impedance 50 Ω nominal    

Product Description: The Rigol DSA815 is a compact and light Spectrum Analyzer with premium performance for portable applications. The use of digital IF (intermediate frequency) technology guarantees reliability and performance to meet the most demanding RF applications. The very large display (20.3 cm / 8") of the Rigol DSA815 Spectrum Analyzer with a resolution of 800x480pixels provides a very good overview over all its comfortable functions like Auto Tune, Auto Range, Auto Scale and Auto Couple. These functions enable the analyzer to acquire signals and match parameters automatically, instead of the manual process necessary with a traditional analyzer. The Rigol Spectrum Analyzers have a sophisticated and easy to use user interface and offers multiple functions for all tasks. The menu navigation is very intuitional in use and all functions and parameters are easy to reach because of the graphical interface.   •9 kHz to 1.5 GHz Frequency Range •Typical -135 dBm Displayed Average Noise Level (DANL) •-80 dBc/Hz @10 kHz offset Phase Noiseppm high frequency stability, -115dBc/Hz low phase noise •Total Amplitude Uncertainty <1.5 dB •100 Hz Minimum Resolution Bandwidth (RBW) •EMI Filter & Quasi-Peak Detector Kit (optional) •VSWR Measurement Kit (optional) •Standard with Preamplifier and AM/FM Demodulation Function •Plenty of measurement functions (optional) •1.5 GHz Tracking Generator (optional) •8 inch (800×480 pixels) high-definition display with clear, vivid, and easy to use graphical interface •Complete connectivity with standard interfaces such as LAN, USB Host, USB Device and GPIB (optional) •Compact size,light weight (9.4 lbs)   Specifications: Spectrum Analyzer Spectrum Analyzer Rigol DSA815 Display 20.3 cm (8") TFT-Color-LCD with 65536 colors Resolution 800 × 480 Pixel Interfaces • USB-Host (for USB stick i.e. to save/load waveforms) • USB for a PC connection • LAN for network connection • GPIB (IEE-488, General Purpose Interface Bus) The GPIB function is only available with the use of the optional available USB GPIB module • VGA interface to connect an external display Dimensions 399 mm × 223 mm × 159 mm (15.71" × 8.78" × 6.26") Weight 6.2 kg (13.67 lbs) 7.5 kg (16.54 lbs) with connected battery. The battery is not included. Supported operation systems Windows XP(32Bit), Vista(32Bit), Windows 7(32Bit)   Function Spectrum Analyzer Rigol DSA815 Channels 1 Frequency Range 9 kHz to 1.5 GHz Frequency Resolution 1 Hz Internal Frequency Reference 10 MHz Span 0 Hz (zero Span) 100 Hz to 1.5 GHz DANL  (Displayed Average Noise level) 100 kHz to 1 MHz   10 MHz to 2 GHz < -90dBm typical: -110dBm < -110dBm-6x(f/1GHz)dB typical: -115dBm DANL (with Preamplifier) (Displayed Average Noise level) 100 kHz to 1 MHz   10 MHz to 1,5 GHz < -110dBm typical: -130dBm < -130dBm-6x(f/1GHz)dB typical: -135dBm Amplitude Range DANL to +20dBm Max. Input Voltage 50 V Sweeptime Range 100 Hz≤Span≤1.5 GHz 0 Hz (zero Span) 10 ms to 2000 s 20 µs to 2000 s Sweepmodes Normal or Single Resolution Filter 100 Hz to 1 MHz (in 1-3-10 sequence) Video Filter 1 Hz to 3 MHz (in 1-3-10 sequence) Input Impedance 50 Ω nominal

Description For installation, inspection and maintenance teams, the C.A 6608 phase rotation tester is an essential tool for identifying the order of the phases on an electrical installation and detecting any phase loss. Identification of the phases makes it easier to ensure correct, safe wiring of your installations, thus preventing damage to the equipment connected to the three-phase networkThe phase order is determined as soon as the cables are connected. The results are displayed on an LCD screen. Specifications: Operating voltage: 40 to 850 VAC between phasesFrequency: 15 to 400 HzPower supply: self-powered via the measurement inputsCompliant with IEC 61557-7Electrical safety: IEC 61010 600 V CAT IIIDimensions/weight: 130 x 69 x 32mm / 130 g

Product Description The Siglent SHA851A handheld spectrum analyzer delivers many powerful measurements and multiple modes of operation. The spectrum analyzer with the built-in pre-amplifier and the optional, independent signal source and the fast scanning speed and high sensitivity, is ideal for broadcast monitoring, channel power scanning, interference localization, monitoring wireless power, electromagnetic compatibility, and other functions. The cable and antenna test mode with the optional DC bias voltage together with a 1-path-2-port vector network analysis function enable the instrument to measure TDR, VSWR, debug port matching, determine insertion loss , debug power amplifier and locate fault location at cables, etc. The Siglent SHA851A handheld spectrum analyzer delivers many powerful measurements and multiple modes of operation. The spectrum analyzer with the built-in pre-amplifier and the optional, independent signal source and the fast scanning speed and high sensitivity, is ideal for broadcast monitoring, channel power scanning, interference localization, monitoring wireless power, electromagnetic compatibility, and other functions. The cable and antenna test mode with the optional DC bias voltage together with a 1-path-2-port vector network analysis function enable the instrument to measure TDR, VSWR, debug port matching, determine insertion loss , debug power amplifier and locate fault location at cables, etc. Inputs and Outputs overview RF input            Port 2 N type female, 50 Ω nomSource               Port 1 N type female, 50 Ω nomUSB Host           USBA plug, version 2.0Ear Phone         Jack 3.5 mmUSB Device       USB C plug, version 2.0LAN                   LAN VXI11 10/100 Base RJ 45GPS Antenna    (GPS Receiver) SMA F 3.3V, 50 ΩBias out(SHA850-BIAS)  SMB F 1 2V 32V 0 .1 V step10 MHz               Reference input 10 MHz, 5 to +10 dBm, BNC  type female, 50 Ω nomExternal trigger   input 1 K Ω 5V TTL level , BNC type female Interference analysis with directional antenna Channel Power and ACPR measurement Siglent SHA851A Features : Spectrum Analyzer Frequency Range from 9 kHz up to 3.6 GHz 1 6 5 dBm /Hz Displayed Average. Noise Level (Typ 10 4 dBc/Hz.@10 k Hz Offset Phase Noise 1 GHz Typ.), 1 Hz up to 10 MHz Minimum Resolution Bandwidth (RBW) Preamplifier and independent signal source up to 3.6 GHz , GPS positioning and logging Cable and Antenna Test Frequency Range from 100 kHz up to 3.6 GHz, Distance To Fault and Time Domain Analysis. Vector Network Analyzer Bias out up to 32VDC Typical working time 4 hours, 3.2 kg net weight, 8.4 lnch Multi Touch Screen , Mouse and Keyboard supported. Remote control Communication Interface : LAN, USB TMC GPIB (USB GPIB adaptorRemote Control Capability :SCPI / Labview / IVI based on USB TMC / VXI 11 / GPIB / Socket / Telnet NI MAX Web Browser (HTML 5 Supported) General Specification: Structure Dimensions310 mm × 215 mm × 78 .5 mm ( W x H x D )Weight Net: 3 2 0 kg 7.0 lb)Display TFT LCD, 800 × 600, 8.4 inch multi touch screen.Storage Internal (Flash) 3 .2 GByte , external (USB storage 32GByte)Working EnvironmentSource AC voltage range 100-240 V, 50/60 Hz or 100-120 V, 400 Hz;Power consumption 20W (typ.)Temperature Working temperature 0 °C to 5 0 °C ,                      Storage temperature 20 °C to 70 °CHumidity        0 °C to 30 °C ≤ 95% Relative humidity                      30°C to 50 °C , ≤ Relative humidityAltitude         Operating: less than 3km 10000 feet)Electromagnetic CompatibilityEN 61326-1: 2013  /    Class A (The active input power of the EUTEN 61000-3 2: 2014     is less than 75 W. According to EN 61000 3 2,                                       no limits are necessary.)EN 61000-3-3: 2013    Plt: 0.65 Pst: 1.00, dmax: 4.00 % dc: 3.00 %                                    dt Lim: 3.30 % dt>Lim: 500msSafetyCAN/CSA-C22.2 No. 61010 1:2012/A1:2018 11CAN/CSA-C22.2 No. 61010 2 030:2018UL 61010 1:2012/R:2018 11UL 61010 2 030:2018RoHS2011/65/EU Model SHA851A SHA852A Frequency Range 9 kHz~3.6 GHz 9 kHz~7.5 GHz DANL -165 dBm/Hz Phase Noise (1 GHz, Typ.) -104 dBc/Hz.@10 kHz Offset Preamplifier Standard Cable and Antenna Analyzer Frequency Range 100 kHz~3.6 GHz 100 kHz~7.5 GHz Vector Network Analyzer(opt.) Frequency Range 100 kHz~3.6 GHz 100 kHz~7.5 GHz Dynamic Range 114 dB Other functions Advanced Measurement Kit, Analog Modulation Analysis, Digital Modulation Analysis, GPS location, Independent Source, DC Bias Out Display TFT LCD, 800 × 600, 8.4 inch multi-touch screen Battery life 4 Hours

WaveMon RF-8 RF Personal Monitor Electric and Magnetic Field Detection  Isotropic sensors with RMS response Weighted response to international standards ICNIRP, European Directive 2013/35/EU, FCC and Safety Code 6 (2015) HIGH INTENSITY AUDIBLE, VISIBLE AND VIBRATORY ALARM  With user definable trigger threshold EXPOSIMETER WITH DATALOGGER  Data collecting and Reporting GPS AND ALTIMETER  Geolocation of measurements HUGE AUTONOMY  More than one month using two rechargeable AA batteries USB COMMUNICATION PORT  Data downloading, set-up and battery charging Datasheet_EN.pdf WEIGHTED RESPONSE The WaveMon has a shaped (weighted) response to specific standards. It is not a single model trying to follow all standards at the same time. That approach will inevitably result in a lack of accuracy. It is available in different models with specific shaping to follow each standard, for increased accuracy. The current available monitors are: WaveMon RF-8 ICN = ICNIRP version WaveMon RF-8 EUD = European Directive 2013/35/EU version WaveMon RF-8 FCC = FCC version WaveMon RF-8 SC6 = Safety Code 6 (2015) version Datalogger The WaveMon is a radio frequency exposimeter that have a datalogger for continuous data recording.Communication with the device is through a USB port that allows you to parametrise the device and download the recorded data. This makes it easy to create reports and allows you to keep a record of your exposure data for your safety. Battery Management Small and lightweight, the exposimeter runs on to rechargeable AA batteries, charged through the USB port.Can also be used with standard AA batteries, so that you can always find replacements.What could be easier? We want to make sure you are always protected. Easy to wear We have created a clip on holder that you can fasten to your harness, belt or arm, so that can take it in your hand and hold it close to a source of radiation, and then put it back easily. You can also fasten the WaveMon RF personal monitor to a small carabiner to keep from dropping it. Fully compliant with ITU-T K.145 The Recommendation ITU-T K.145, issued by the International Telecommunication Union, recommends that RF personal monitors (exposimeters) be equipped with a list of basic features in RF safety for RF workers worldwide.The WaveMon is fully compliant with this Recommendation. In addition, Wavecontrol is member of the National Association of Tower Erectors (NATE) in the US, organization promoting the highest standards of safety for Tower Climbers and RF Workers. Exposimeter Main features According to the international standards on EMF safety. E-field measurements up to 8 GHz and H-field measurements up to 1 GHz. Isotropic sensors. RMS detection. Weighted response for direct comparison to a specific limit: ICNIRP, European Directive 2012/35/EU, FCC or Safety Code 6 (2015). High intensity audible, visible and vibratory alarms. Optional GPS and Altimeter. User-defined alarm threshold. Datalogger for reporting and historical registry of data. PC USB connection for data downloading and configuration. Small and light. Powered by two standard AA batteries, disposable or rechargeable through its USB port. More than 200 hours autonomy.

Product Description LC\APC – LC\UPC 5m : Single mode Duplex Patchcord Shipping Not Included

Product Description The SIGLENT SSG5060X signal generator can generate analog and vector signals, with a frequency range of 9kHz to 4GHz. The SSG5000X series features the industry-leading performance in phase noise, spectral purity, bandwidth, EVM, output power measurements and tests. The internal IQ modulation generator and waveform playback function make it easy to create even the most complex signal types. They also cover the most important RF band for digital wireless communications and includes standard waveform files.The SIGLENT SSG5040X is a powerful and cost effective source that are ideal for R&D, education and manufacturing. User interface SSG5000X Series 1. Prompt status bar 2. RF frequency 3. RF level 4. Touch screen display area: Displays the settings under each menu Use an external USB power sensor to compensate cable losses Key Features SSG5060X : Frequency up to 6GHz 0.001 Hz frequency setting resolution Maximumoutput power up to +26 dBm (typ.) Phase Noise: -120 dBc/ Hz @ 1 GHz, 20 kHz offset (typ.) User programmable flatness correction. Provides AM,FM,PM analog modulation with internal,external or Int+Ext source. Single pulse, double pulse and pulse traingenerator (option) Built-in digital communication standard waveform files such as 5G-NR, LTE, WCDMA, WLAN, Blue-Tooth，CDMA Internal Custom mode generate common IQ signals such as QAM, FSK, ASK, MSK. Analog differential I/Q outputs External analog I/Q input USB-power meter measurement 5 inch TFT capacitieve touch screen,mouse and keyboard supported Webbrowser remote control on PC and mobile terminals. Standard interfaces includes USB Host,USB Device (USBTMC), LAN (VXI-11,Socket, Telnet). Optiona linterface: GPIB ARB mode to clip the signal of the peak power and display the CCDF (cytotoxic cell diff. factor) Accessoires Included: 1 x Siglent SSG3060X Signal Generator1 x Quick start Guide1 x Guarantee Card1 x Power Cord1 x USB Cable

Product Description The SIGLENT SSG5040X-V signal generator can generate analog and vector signals, with a frequency range of 9kHz to 4GHz and IQ modulation 10 MHz to 4GHz. The SSG5000X series features the industry-leading performance in phase noise, spectral purity, bandwidth, EVM, output power measurements and tests. The internal IQ modulation generator and waveform playback function make it easy to create even the most complex signal types. They also cover the most important RF band for digital wireless communications and includes standard waveform files.The SIGLENT SSG5040X is a powerful and cost effective source that are ideal for R&D, education and manufacturing. User interface SSG5000X Series 1. Prompt status bar 2. RF frequency 3. RF level 4. Touch screen display area: Displays the settings under each menu Use an external USB power sensor to compensate cable losses Key Features SSG5040X-V : Frequency up to 4GHz 0.001 Hz frequency setting resolution Maximumoutput power up to +26 dBm (typ.) Phase Noise: -120 dBc/ Hz @ 1 GHz, 20 kHz offset (typ.) User programmable flatness correction. Provides AM,FM,PM analog modulation with internal,external or Int+Ext source. Single pulse, double pulse and pulse traingenerator (option) Internal IQ modulation with 150 MHz modulation bandwidth with perfect in-factory calibration. Built-in digital communication standard waveform files such as 5G-NR, LTE, WCDMA, WLAN, Blue-Tooth，CDMA Internal Custom mode generate common IQ signals such as QAM, FSK, ASK, MSK. Analog differential I/Q outputs External analog I/Q input USB-power meter measurement 5 inch TFT capacitieve touch screen,mouse and keyboard supported Webbrowser remote control on PC and mobile terminals. Standard interfaces includes USB Host,USB Device (USBTMC), LAN (VXI-11,Socket, Telnet). Optiona linterface: GPIB ARB mode to clip the signal of the peak power and display the CCDF (cytotoxic cell diff. factor)

Product Description The advanced MSO8104 1GHz 4-channel Digital Oscilloscope offers 10GSa/sec maximum sample rate, and 500 Mpts memory depth.  An optional 16-channel logic analyzer interface is provided to add digital debug capabilities. A two-channel 25MHz arbitrary waveform generator is also available. The 10.1” 1024 x 600 capacitive multi-touch color LCD screen also offers 256-level intensity grading and waveform refresh rate of up to 600,000wfm/sec.   The enhanced FFT capability offers real-time spectrum analysis of up to 1Mpts of waveform data.  The MSO8000 Series Next Generation User Interface provides users with five distinct ways to interact with the instrument: LCD Touch, traditional button and knob, mouse/monitor, PC control and remote web operation. The MSO8000 series adopts Rigol’s proprietary “Phoenix” chipset, which allows sampling at 10GSa/s and integrates all of the front-end analog processing.  The three models (600MHz, 1GHz, and 2GHz) in the MSO8000 series provide non-stop recording and playback for a maximum of 450,000 frames of hardware real-time waveforms using a segmented storage technique.  Trigger conditions can be set to make a selective choice in capturing and saving the signals of interest. With a total of seven unique integrated instruments (digital oscilloscope, 16-channel logic analyzer, spectrum analyzer, optional arbitrary waveform generator, digital voltmeter, 6-digit frequency counter and totalizer, and optional protocol analyzer, 43 Precision Measurements, Power, Histogram, FFT and other analysis capabilities, the MSO8000 Series allows customers to quickly identify and resolve complex design and debug challenges. The optional Protocol Analyzer supports RS232/UART, I2C, SPI, CAN, LIN, I2S, FlexRay, and MIL-STD-1553 serial bus.  The protocol trigger and decoding operate on both the analog channel and the digital channels: RS232/UART, I2C, and SPI protocols, which also a support the waveform search function. The Jitter firmware option supports real-time eye diagram and jitter analysis. The range is field-upgradeable to higher bandwidths. The MSO8000 series is equipped with hardware pass/fail test function as the standard configuration, which can be used in signal monitoring for a long time, signal monitoring during design, and signal test in the production line.  Set the test mask based on a known "standard" waveform, and then an automatic comparison with the signal under test can show a successful or failed test. The MSO8000 series provides a variety of external interfaces, including USB HOST&DEVICE, LAN(LXI), HDMI, TRIG OUT, and USB-GPIB (option). The oscilloscope is in compliance with the standards specified in LXI Device Specification 2011. It can access to the LXI webpage via the LAN interface. Features Analog bandwidth: 600 MHz, 1 GHz, and 2 GHz (single-channel and half-channel modes) 4 analog channels, 1 EXT channel, and 16 standard configuration of digital channels (required to purchase the probe) Up to 10 GSa/s real-time sample rate Up to 500 Mpts memory depth (standard) High waveform capture rate (over 600,000 waveforms per second) Up to 450,000 frames of hardware real-time and ceaseless waveforms recording and playback functions Integrates 7 independent instruments into 1, including digital oscilloscope, 16-channel logic analyzer, spectrum analyzer, arbitrary waveform generator (option), digital voltmeter, 6-digit frequency counter and totalizer, and protocol analyzer (option) Auto measurement of 41 waveform parameters; full-memory hardware measurement function A variety of math operations, built-in enhanced FFT analysis, and peak search function Waveform histogram analysis (standard) Independent search, navigation keys, and event table Real-time eye diagram and jitter analysis software (option) Built-in advanced power analysis software (option) User-defined one-key quick operation 10.1-inch capacitive multi-touch screen, 256-level intensity grading display, with color persistence Multiple interfaces available: USB HOST&DEVICE, LAN(LXI), HDMI, TRIG OUT, and USB-GPIB Web Control remote command Unique online version upgrade Sophisticated and convenient industrial design, easy to operate Includes USB cable [CB-USBA-USBB-FF-150] 4 passive high-impedance probes (500 MHz) [RP3500A] 2 passive low-impedance probes (1.5 GHz, only for MSO8204/MSO8104) Front panel cover [MSO8000-FPC] Quick guide (hard copy)

Product Description Siglent SPL1016 logic analyzer probe for SDS1000X scopes with license key. Parameters : SPL1016 Channels 16 Input Impedance 100 KΩ||8 pF Max. Input Voltage ±20 V peak Threshold Groupings Pod 2: D15-D8 Pod 1: D7-D0 Threshold Selections TTL (1.5 V), COMS (2.5 V), 3.3 V_LVCOMS (1.65 V), 2.5 V_LVCOS (1.25 V) User defined threshold range ±3 V in 10 mv steps Threshold Accuracy ±（3%*Threshold+150 mv） Input Dynamic Range ±10 V Min. Input Voltage Swing 800 mVpp Max. Input Frequency 60 MHz Min. Detectable Pulse Width 8.3 ns Channel Skew ±(1 digital sample interval)

Product Description Siglent SLA1016 is a mixed Signal Hardware Option for the Four Channel SDS1000X-E and SDS2000X-E Oscilloscope Series. NOTE: Four channel SDS1000X-E scopes require firmware version 7.1.6.20 or greater Parameters : SLA1016 Channels 16 The kit includes: 1 x License key1 x SBus Controller1 x SBus cable1 x Wiring Harness20 x Digital clips

Product Description Siglent SPL2016 16 Channel logic probe module with license key for SDS2000X Oscilloscopes. 

Product Description Siglent SPL2016 16 Channel logic probe module HARDWARE ONLY no license. This probe can be used for the SDS2000X and SDS5000X Series oscilloscopes.

FiberFox Mini 4S+ The Most Complete Fusion Splicer Kit  : Active Alignment Splicer – 4 Motors Size: 4.8 x 4.88 x 5.4 (in)Weight: 2.88lbs. (w/o battery) Fastest Splicing Time6 sec with single mode fiber (quick mode)10 sec Heating time* 6 sec with continuous heating mode Comes with 2 Battery PacksFull Touch ScreenSOC Compatible Included:Thermal Stripper and Precision Cleaver ++ 1. The Smallest and the Lightest Active Alignment Fiber Fusion Splicer 2. Guaranteed Stability and Splicing Performance 3. SOC Compatible 4. Features

Product Description Mango is new standard core alignment splicing machine covering various splicing needs, such as multi-function fiber holder, integrated cooling tray, SOC slider, 8s splicing, 24s heating etc.. All these are made for efficient splicing. - 5 inch color LCD display- 8s splicing, 24 heating time- Multi-function fiber holder- Integrated cooling tray- Graphical buttons and Smart GUI interface- Simultaneous X and Y views with 200 times magnification,300 times magnification X or Y view Specification * Applicable Fibers:  SM, MM, DS, NZDS, EDF * Splicing Fiber Number:  Single core * Average Splicing Loss:  0.02dB(SM),0.01dB(MM),0.04dB(DS),0.04dB(NZDS),0.04dB(BIF/UBIF) * Splicing Mode:  Auto & Manual & Half Auto * Splicing Setting:  100 groups customize * Splicing Time:  Typical 8s with standard SM fiber * Heating Time:    24 * Electrode Life:  2500 * Tension Test:  2.0N(Standard) * LCD:  5.0 inch color LCD * Language:  English or customize * Fiber Magnification: X/Y:180 times,X or Y:360times * Storage: 10000 groups * Data Connector: USB 2.0 * Power Supply: Li-ion battery or AC/DC input:13.5V * Battery Capacity: Typical 200 cycles(splicing and heating) * Environmental Conditions:  -10~+50℃(operation temperature),0~95% RH(humidity),0~5000(altitude) * Size(H*W*D):  164mm * 141mm * 138mm * Weight:  1.83kg

Product Description Satlink WS-6980 DVB-S2 +DVB-C+DVB-T2 MPEG4 HD Optical power detection COMBO Satellite Finder Meter 7 Inch High Definition TFT LCD Screen(1024*600)Fully DVB-S/S2,T/T2/C, MPEG-2/MPEG-4 compliantMPEG-2 / MPEG-4 H.264 Hardware decodingSupports scan of Auto, Manual ,NIT(DVB-S/S2)Supports scan of blind (DVB-S/S2/C)Supports Constellation analyzerSupports Spectrum analyzerSupports for multiple CH/TP detectionSupports Alarm for Locking SignalAuto Calculate Angle of AZ ,ELSupports DISEQC 1.0/1.1/1.2 ,0/22khz ToneStereo pairs of speakersSupports both AV IN/OUTSupports HDMI IN/OUT out and AV inSupports the DC12V output Electronic compassLNB, ANT, DC12V short protectThe built-in flashlight Optical power detection7.4V/5000mAh Li-ion BatteryIndependent battery charging powerSoftware upgrade via USB port

Product Overview SDM3045X is a 4½ digit digital (60000 count) multimeter incorporating a dual-display and is especially well suited for the needs of high-precision, multifunction and automatic measurement. Key Features ◆ Real 4½ digit (60000 count) readings resolution ◆ Up to 150 rdgs/s measurement speed ◆ True-RMS AC Voltage and AC Current measuring ◆ 1 Gb NAND flash size, Mass storage configuration files and data files ◆ Built-in cold terminal compensation for thermocouple ◆ With easy, convenient and flexible PC software: EasyDDM ◆ Standard interface: USB Device, USB Host, LAN  ◆ User-friendly Design      • 4.3” TFT-LCD, 480*272      • Support dual display, Chinese and English Menu      • Built-in front panel accessible help system      • File management (support for USB Driver and local storage) ◆ USB & LAN remote interfaces support common SCPI command set. Compatible with other popular DMMs on the market. Application fields     •  Research Laboratory    •  Development Laboratory    •  Detection and Maintenance    •  Calibration Laboratory    •  Automatic Production Test

Description The ORITEL BDH R100 microwave training bench has been developed to meet teaching and adult training requirements in civil and military contexts. Uses the rectangular standard waveguide R100/WR90 technique. Frequency range from 8.5 to 9.6 GHz. Equipped with the EASYFIX™ fast assembly system Study of the GUNN oscillator Wavelength measurement Standing wave ratio measurement Impedance measurement Frequency measurement Reading the quadratic law of a detector, etc. This microwave training bench comes with detailed course material and practical exercises comprising 14 components. State of Delivery 1-ORITEL OSG 100 GUNN diode oscillator 1-ORITEL ISO 100 ferrite isolator 1- ORITEL MOD 100 PIN  diode modulator 1- ORITEL ATM  variable  attentuator  1- ORITEL OND 100 cavity wavemeter with curve 1- ORITEL LAF 100 measuring line 1- ORITEL ADZ 100/3 impedance adaptor 1-ORITEL TGN 100 waveguide -to-coax transition element 1-ORITEL DEN 100 coaxial detector  1- ORITEL  CHG 100 adapted load  1-ORITEL CC 100 short circuit platelet  3- ORITEL SUP 100 guide support

Advantages Single-phase, split-phase and three-phase installations with or without a neutral, as well as other complex configurations. Implementation without cutting off the mains power supply BlueTooth, Ethernet and USB communication Automatic recognition of the sensors connected Recording on SD and SD-HC cards Real-time communication with a PC and analysis using PEL Transfer Description Ergonomic, magnetized and suitable for all types of cabinets, PEL102 loggers provide all the power and energy measurements simultaneously. Other specifications: Voltage up to 1,000 V Current up to 10,000 A Voltage ratio / current ratio up to 650,000 V / up to 25,000 A Power from 10 W/var/VA to 10 GW/Gvar/GVA Energy up to 4EWh / 4 EVAh / 4 Evarh Phase: cos φ, tan Φ, PF Harmonics up to 50th order 2 GB SD memory card (SD-HC card up to 32 GB)

Description The C.A 5273 is a comprehensive multimeter for electrical maintenance of installations and small AC and DC machines, with a double 6,000-count backlit display and a 61+2-segment bargraph with remanent effect. Its 600V CAT IV safety is backed by IP54 ingress protection. Designed and manufactured in France by CHAUVIN ARNOUX, this multimeter comes with a 3-year warranty. CAT IV 600V / CAT III 1,000V TRMS measurements Bi-mode double 6,000-count backlit display and 61+2-segment bargraph (full scale / central zero) Auto AC/DC selection Automatic or manual range selection VLowZ low-impedance voltage measurement with low-pass filter 1,000 V 10 A Resistance / audible continuity Temperature Capacitance Max / Min storage 3-year warranty  Equivalent to APPA 73/ Fluke 177

Description This compact, comprehensive digital multimeter is equipped with all the functions required by electricians for maintenance of low and medium-power residential and tertiary equipment and installations. Ergonomic and simple to use, it is exceptionally easy to read with its 6,000-count backlit display with bargraph, 2 "Off" positions for greater effectiveness and a compact casing with a non-slip protective coating for excellent handling. CAT IV 600V TRMS measurements Large 6,000-count backlit display (digits 8 mm high) 61-segment bargraph Double OFF position No-contact voltage detection  (NCV) VLow Z low-impedance voltage measurement to avoid stray voltages. Min, MAX and RELative functions Measurement up to 1,000 V AC or DC current measurement up to 10 A Frequency measurement Temperature measurement Capacitance measurement 60 mV range Compact IP54 casing with built-in shockproof protection Compatible with the multi-function mounting accessory Equivalent to Fluke 115 & 117

Advantages Large LCD for multi-parameter display on 70x52 mm screen. A simple basic multimeter with surveillance of the main functions: Min, Max, Avg and Peak+/- . Digital keyboard with lighting. Optimized ergonomics: IP67 leakproof casing, IEC61010 600V CAT III/300V CAT IV safety measurement terminals, power supply by normal battery or Ni-MH rechargeable battery (external charger) and contextual reminder of connections on screen. Description ASYC IV MTX 3290 - The reference for multimeters These portable multimeters with digital display allowing direct measurement of the main electrical quantities benefit from an innovative design making them compact, rugged, leakproof and comfortable to grip. Simple multimeters • Easy-to-read 70x52 mm LCD screen • Contextual reminder of connection on the screen • Current autoranging, single terminal up to 10 A • Secondary measurements in addition to the main measurement to facilitate analysis • Surveillance of the MIN/MAX and AVG data with relative time/date-stamping and of voltage and current peaks And much more... • IP67 protection against water projection and dust,ideal for outdoor conditions • Powered by 4 standard AA batteries or 4 Ni-MH batteries rechargeable with an HX0051B external module (option) • Operation for up to 400 hrs on batteries

Description With its IP54 protection, the design of the C.A 5271 is particularly compact, making it very easy to handle. To make it easy to read, the double 6,000-count display is equipped with a 61 + 2-segment bargraph with dual-mode remanent effect. For greater effectiveness, the bargraph is equipped with a central zero.In safety terms, the C.A 5271 can be used for all 600 V CAT IV applications.The C.A 5271 is designed and manufactured in France by CHAUVIN ARNOUX and comes with a 3-year warranty. CAT IV 600V / CAT III 1,000V TRMS measurements Large 6,000-count display and 61+2-segment bargraph Auto AC/DC selectioon Autorange VLowZ low-impedance voltage measurement with low-pass filter 1,000 V 10 A Resistance / audible continuity IP54 3-year warranty Equivalent to APPA 72 / Fluke 175

This compact digital multimeter meets the needs of any self-employed electrician. It is simple to use and exceptionally easy to read thanks to its 6,000-count backlit display with bargraph. There are two "Off" positions for greater effectiveness, including one which allows no-contact voltage detection. The screen lights up when near to a live cable. If it is hooked up to a current clamp, it can measure currents up to 600 A in total safety. CAT IV 600V / CAT III 1,000V TRMS measurements Large 6,000-count backlit display (digit height: 8 mm) 61-segment bargraph Compact casing with built-in shockproof protection Double OFF position NCV (no-contact voltage detection) VLow Z low-impedance voltage measurement to avoid stray voltages. Measurement up to 1,000 V 60mV range AC or DC current measurement up to 600 A with current clamp (1mv/A AC or DC) with direct reading of the measurement in Amperes IP54 Compatible with the multi-function mounting accessory Equivalent to Fluke 114

Description Ergonomic and compact: the multi-function analyser-oscilloscope with a touch screen OSCILLOSCOPE + MULTIMETER + RECORDER + HARMONIC ANALYSER The OX 6062B oscilloscope is also a "real-time" FFT analyser. With its 2 x 300V Cat. II measurement channels, it can display up to 4 curves on screen. Equipped with a removable SD card, the OX 6062B's recording and storage capacity has now been increased to 2 GB! In addition, the SD versions come with a Lifetime Warranty*. These ergonomic, compact instruments include a storage space for stowing the cables and probes. On the front panel, 28 command keys are directly accessible and "Windows-like" menus make the OX 6000 even simpler to use. Other specifications: Display: LCD with backlighting, 4 curves + 4 references. Bandwidth: 60 MHz Vertical resolution: 10-bit converter and 4-digit display Wide dynamic input range: 2.5 mV to 100 V/div Memory depth: 2,500 points/channel and up to 50,000 points/channel with the Extended Acquisition Memory option Advanced triggering: Auto, Normal, One-shot, Auto level 50 %, CH1, CH2, EXT, LINE, Edge, Pulse Width, TV Frame, TV Line, Hold-off Multimeter: 2 x 4,000-count channels + min/max bargraph, time/date-stamped graphic recording Other measurements: resistance, continuity, capacitance, frequency, temperature, diode test. Communication: local Ethernet, RS232 & USB Network: 10 MB Ethernet, ScopeNet web server (remote control, "real-time" trace, cursors and automatic measurements, FTP server (for exchanging files with a PC), FTP client (storage on PC hard disk),ScopeAdmin administration utility, "SX-Metro" application software for PC and ANDROID application available from GOOGLE STORE.

  Description The OX 6202B oscilloscope is also a "real-time" FFT analyser. With its 2 x 300 V Cat. II measurement channels, it can display up to 4 curves on screen. Equipped with a removable SD card, the OX 6202B's recording and storage capacity has now been increased to 2 GB! These ergonomic, compact instrument include a storage space for stowing the cables and probes. On the front panel, 28 command keys are directly accessible and "Windows-like" menus make the OX 6202B even simpler to use. Other specifications: Additional specifications: Display: LCD with backlighting, 4 curves + 4 references. Bandwidth: 200 MHz Vertical resolution: 10-bit converter and 4-digit display Wide dynamic input range: 2.5 mV to 100 V/div Memory depth: 2,500 points/channel and up to 50,000 points/channel with the Extended Acquisition Memory option Advanced triggering: Auto, Normal, One-shot, Auto level 50 %, CH1, CH2, EXT, LINE, Edge, Pulse Width, TV Frame, TV Line, Hold-off Multimeter: 2 x 4,000-count channels + min/max bargraph, time/date-stamped graphic recording Other measurements: resistance, continuity, capacitances, frequency, temperature, diode test. Communication: local Ethernet, RS232 & USB Network: 10 MB remote Ethernet, Web server (remote control, "real-time" trace, cursors and automatic measurements, FTP server (for exchanging files with a PC), FTP client (storage on PC hard disk), administration utility "SX-Metro" application software for PC

Description The METRIX® DOX2000 Series oscilloscopes are particularly compact and simple to use, with a casing specially designed for laboratory use. They are equipped with a wide display offering 18 div. in full-screen mode. This allows customization of the display: choice between normal or persistent display, YT or XY format, adjustment of the colours, graticule, brightness, contrast, etc. Rotary buttons and backlit keys give access to the commands on the front panel. With its handle, the DOX oscilloscope is easy to transport and its non-slip feet make it particularly stable.High performance and multiple functions for acquisition and analysisThere are 3 acquisition levels for acquisition and analysis, in real time or equivalent time. The memory depth for acquisition is 32 kpoints or 2 MPoints to optimize your analyses. The vertical sensitivity is from 2 mV/div. to 10 V/div. with 12 ranges and the horizontal sensitivity is from 2.5 ns to 50 s/div. Advanced functions are also available: simple MATH functions (+/-/x/÷) and "real-time" FFT with simultaneous display of the traces.The EASYSCOPE software delivered with the product can be used to control and test the oscilloscope and to recover the trace and screenshot files. Technical specifications: - 7-inch ¼ VGA colour display- Full menus in 5 languages + on-screen contextual help in English- 2-channel measurement capture + Ext Trig and complex triggers- Vertical resolution: 8 bits- 32 automatic measurements + cursors- USB host and device communication- IEC 61010-1 / 300 V CAT II2 x 100 MHz channels - Sweep speed from 2.5 ns/div. to 50 s/div. Sampling rate: one-shot = 500 MS/s (2 channels), 1 GS/s (one channel) / Repetitive = 50 GS/s Max. memory depth: 2 Mpoints

Description The METRIX® DOX2000 Series oscilloscopes are particularly compact and simple to use, with a casing specially designed for laboratory use. They are equipped with a wide display offering 18 div. in full-screen mode. This allows customization of the display: choice between normal or persistent display, YT or XY format, adjustment of the colours, graticule, brightness, contrast, etc. Rotary buttons and backlit keys give access to the commands on the front panel. With its handle, the DOX oscilloscope is easy to transport and its non-slip feet make it particularly stable.High performance and multiple functions for acquisition and analysisThere are 3 acquisition levels for acquisition and analysis, in real time or equivalent time. The memory depth for acquisition is 32 kpoints or 2 MPoints to optimize your analyses. The vertical sensitivity is from 2 mV/div. to 10 V/div. with 12 ranges and the horizontal sensitivity is from 2.5 ns to 50 s/div. Advanced functions are also available: simple MATH functions (+/-/x/÷) and "real-time" FFT with simultaneous display of the traces.The EASYSCOPE software delivered with the product can be used to control and test the oscilloscope and to recover the trace and screenshot files. Technical specifications: - 7-inch ¼ VGA colour display- Full menus in 5 languages + on-screen contextual help in English- 2-channel measurement capture + Ext Trig and complex triggers- Vertical resolution: 8 bits- 32 automatic measurements + cursors- USB host and device communication- IEC 61010-1 / 300 V CAT II2 x 40 MHz channels – Sweep speed from 2.5 ns/div. to 50 s/div. Sampling rate: one-shot = 500 MS/s (2 channels), 1 GS/s (one channel) / Repetitive = 50 GS/s Max. memory depth: 2 Mpoints

Description The METRIX® DOX2000 Series oscilloscopes are particularly compact and simple to use, with a casing specially designed for laboratory use. They are equipped with a wide display offering 18 div. in full-screen mode. This allows customization of the display: choice between normal or persistent display, YT or XY format, adjustment of the colours, graticule, brightness, contrast, etc. Rotary buttons and backlit keys give access to the commands on the front panel. With its handle, the DOX oscilloscope is easy to transport and its non-slip feet make it particularly stable.High performance and multiple functions for acquisition and analysisThere are 3 acquisition levels for acquisition and analysis, in real time or equivalent time. The memory depth for acquisition is 32 kpoints or 2 MPoints to optimize your analyses. The vertical sensitivity is from 2 mV/div. to 10 V/div. with 12 ranges and the horizontal sensitivity is from 2.5 ns to 50 s/div. Advanced functions are also available: simple MATH functions (+/-/x/÷) and "real-time" FFT with simultaneous display of the traces.The EASYSCOPE software delivered with the product can be used to control and test the oscilloscope and to recover the trace and screenshot files. Technical specifications: - 7-inch ¼ VGA colour display- Full menus in 5 languages + on-screen contextual help in English- 2-channel measurement capture + Ext Trig and complex triggers- Vertical resolution: 8 bits- 32 automatic measurements + cursors- USB host and device communication- IEC 61010-1 / 300 V CAT II2 x 25 MHz channels – Sweep speed from 25 ns/div. to 50 s/div. Sampling rate: one-shot = 250 MS/s (2 channels), 500 MS/s (one channel) / Repetitive = 10 GS/s Max. memory depth: 32 kpoints

Description Multi-function installation testerComplete and lightweight, the MX 435D multi-function tester offers all the essential functions for checking the safety of electrical installations in accordance with the applicable standards: NF C 15-100,EN 61557 (1-2-4-5-6), VDE 0100, IEE 16 th, IEC 64-8, OVE EN-1, RBT MIE. Specially designed for self-employed electricians, installers, certification organizations and maintenance teams, it represents a good compromise in terms of price and performance.Main technical specifications: • Measurements: -Insulation: 0.5 to 199.9 MΩ -Continuity with buzzer: 0.10 to 19.99 Ω -Insulation at 500 V: 0.50 to 199.9 Ω -Earth resistance: 0.10 to 1,999 Ω -Earth loop: 0.10 to 19.99 Ω / 20 to 1,999 Ω-RCD test: 30 mA / 100 mA / 300 mA / 500 mA / 650 mA calibres 1 x IΔn pulse mode-Voltage: 0 to 600 VAC -Current and leakage current (with clamp): 2 A / 200 A ranges• Immediate, error-free connection thanks to colour coding of the terminals and the switch • Fuseless protection against external voltages• Electrical safety: IEC 61010, 300 V CAT III

Description For installation, inspection and maintenance teams, the C.A 6609 can be used to identify the phase order on an electrical installation and the rotation direction of any motor, with or without contact. Identification of the phases ensures correct, safe wiring of the installations or motors, thus preventing damage to the equipment connected to the three-phase networkThe C.A 6609 can be used to quickly determine the phase order and detect any phase loss. It also includes additional dedicated functions for industrial equipment (motors, pumps, etc.): indication of the rotating field direction without connection determination of the connection direction of the phase wires These various tests are carried out as soon as the cables are connected, for the phase order, and by simply pressing a button for industrial equipment testing. The results are indicated by LEDs which are easy to interpret.Comprehensive and easy to use thanks to the colour-coding of the terminals and cables, this instrument is ideal for inspection and maintenance teams in industrial buildings. It is delivered with all the accessories needed for the various tests.Functions and technical specifications: Automatic testing as soon as the connections are set up Indication of phase presence or absence Determination of a motor's rotation direction with or without contact Operating voltage: 40 to 600 VAC between phases with connection / 120 to 400 VAC between phases without connection Frequency: 15 to 400 Hz Electrical safety: IEC 61010 600 V CAT III Dimensions/weight: 130 x 69 x 32mm / 130 g

Description The C.A 6117 is an ALL-IN-ONE instrument for testing electrical installations in compliance with the national and international standards (IEC 60364-6, NF C 15-100, VDE 100, XP C 16-600, etc). It combines design, ergonomics, simplicity, performance, rapidity and accuracy.Suitable for all neutral systems (TT, TN, IT), it is ideal for all sectors: industry, tertiary and residential. Ergonomics The rugged, compact C.A 6117 is specially designed for quick and effective familiarization. On its large LCD graphical colour display with backlighting, users can view all the crucial results at a glance. A rotary switch on the instrument’s front panel gives direct access to all the functions. A large number of visual symbols and audio signals help with quick interpretation of the results in accordance with the standards. The on-line contextual help menus can guide the user step by step, if needed. The storage capacity can save up to 1,000 tests. The C.A 6117 also has a USB output for data transfer. Measurements The high-performance C.A 6117 offers excellent measurement stability, even in disturbed industrial environments. All the measurements needed to test an electrical installation are available: continuity, resistance, insulation, earth and selective earth, loop impedances, type A and AC RCDs. The C.A 6117 can also be used to measure voltage, frequency, current via a clamp, active power, harmonics and phase rotation. The C.A 6117 is also fitted with type-B RCD testing, built-in fuse table and voltage drop feature. Designed and manufactured in France, the C.A 6117 was developed in compliance with eco-design procedures. Analysis of the resultsThe measurements made with the C.A 6117 can be processed by the DataView® multi-product expert processing software. DataView® automatically recognizes the instrument when it is connected to the PC and opens the corresponding menu. By means of a tree structure, it offers users direct access to the data recorded in the instrument, its configuration, etc. It is equipped with multiple predefined report templates which comply with the standards' requirements. Users can also create their own templates, as required. Delivered as standard, the ICT software offers the following functions for quick, simplified analysis of the recorded measurements: recovery of the data, configuration of the instrument, customization of measurement campaigns with transfer into the instrument and generation of reports. Accessories Delivered in a bag with a large number of accessories, a wrist strap and a 4-point harness are also available as standard features for "hands-free" use.

Description The C.A 6113 is an ALL-IN-ONE instrument for testing electrical installations in compliance with the national and international standards (IEC 60364-6, NF C 15-100, VDE 100, XP C 16-600, etc). It combines design, ergonomics, simplicity, performance, rapidity and accuracy. Suitable for all neutral systems (TT, TN, IT), it is ideal for all sectors: industry, tertiary and residential.ErgonomicsThe rugged, compact C.A 6113 is specially designed for quick and effective familiarization. On its large backlit B&W graphical screen, users can view all the crucial results at a glance.A rotary switch on the front of the instrument gives direct access to all the functions. A large number of audio and visual symbols are available for quick interpretation of of the results according to the standards.The contextual help for each function guides the user step-by-step or only when required. The high-performance C.A 6116 offers excellent measurement stability, even in disturbed industrial environments.AccessoriesDelivered in a bag with a large number of accessories, a wrist strap and a 4-point harness are also available as standard features for "hands-free" use.

Description Innovative and particularly user-friendly, the C.A 6030 RCD is particularly easy to use and offers high metrological performance for the testing protection systems and installations' compliance with the European and international standards NF C 15-100, VDE 0100, NIN/NIV, IEEE 16th, ÖVE EN-1. Direct, safe connection to installation mains socket Reliable measurements due to automatic permutation of L and N inputs if conductors are reversed at socket connection Automatic installation voltage and frequency measurement Tests standard, selective, A and AC RCDs 5 fixed ranges 10/30/100/300/500 mA + 1 adjustable range from 6 to 650 mA RCD non-trip test / trip time measurement (pulse or ramp mode) and exact trip current (ramp mode) Power-on earth measurement: earth loop and 1P earth Current and leakage current measurement with clamp (option) Phase rotation test (2 or 3-wire) Cat.III 600 V Programmable alarms, date-stamped recording of measurement readings, data printout using standard printer, direct transfer of data to PC (transfer software included as standard) Large backlit display / "hands-free" bag Battery-powered - battery life: 2,000 tests Dimensions: 270 x 250 x 60 mm; weight: 900 g

Advantages Direct access to the main functions (configuration, etc.) Direct access to the measurements (harmonics, flicker, etc.) Voltage/current inputs with colour-coded inserts Large colour TFT screen for easy reading Battery life of 13 hrs Description All the parameters simultaneously Designed for test and maintenance departments working in industrial or administrative buildings, the Qualistar+ C.A 8331 can be used to obtain a snapshot of the main features characterizing the quality of the electrical network. Easy to handle and particularly compact, this instrument also offers a large number of calculated values and several processing functions. The C.A 8331 is equipped with 3 voltage measurement channels and 3 current measurement channels. When the current sensors are connected to the C.A 8331, it recognizes them automatically. It also offers the possibility of mixing different types of current sensors and configuration of the ratios allows direct reading of the measurements. The Qualistar+ is specially designed for work in the field: The multiple functions of the Qualistar+ C.A 8331 make it particularly versatile. It is suitable for applications up to 1,000 V in CAT III and 600 V in CAT IV.The measurements obtained with the Qualistar models can be processed using two software tools: PAT delivered as standard and Dataview®, available as an option. Technical specifications: TRMS AC+DC voltage and current, frequency Power values: W, VA, var, VAD, PF, DPF, cos φ, tan φ Energy values: Wh, varh, VAh, VADh, , BTU, toe, Joule Harmonics from 0 to the 50th order, phase Flicker (Pst and Plt) Recording of a selection of parameters at the maximum sampling rate over a period from 4 hrs to 2 weeks Peak detection Vectorial representation IP53 / IK08 USB communication Dimensions / weight: 240 x 180 x 55 mm / 1.9 kg

Advantages C.A 8435, the rugged, waterproof IP67 Qualistar+: Indoor and outdoor use, even when it is raining5 voltage inputs, 4 current inputsContinuous recording of all the parameters simultaneouslyMonitoring with alarmsAll types of installations Description The "all-terrain" Qualistar for all seasons! The Qualistar Plus power and energy quality analyser is ideal for quick network quality checks and effective analysis of the results. EVEN MORE NEW FEATURES! Version V4 of the Qualistar+ includes major new functions: Inrush over a period of up to 10 minutes Integration of all the DC components Calculation of the distortion voltages and currents Measurement of P, Q, S and D power values, total and per phase Calculation of Pst & Plt flicker values Large choice of units available: kW, Joule, nuclear toe, non-nuclear toe, BTU, etc. Up to 40 alarms can be set simultaneously! Recording mode: recording starts immediately Specially designed to save time! Ideal for the needs of inspection and maintenance departments, the Qualistar models are designed for quick verification of network quality and simple processing of the results. The keyboard is divided into immediately-identifiable areas (direct functions, Pop-up menus, cursor, etc.) and the wide colour screen (diagonal 148 mm) uses the same pictograms as the keyboard. The display modes are structured. These direct-access functions help save extra time.Specific caps have been developed to ensure that the C.A 8435 analyser is waterproof.

Advantages All the measurements required in a single instrument Proven, acknowledge simplicity of use Extra-long recording duration Capture of transients lasting just a few µs Inrush mode with waveform Description All the parameters simultaneously Designed for test and maintenance teams working in industrial or administrative buildings, the Qualistar+ C.A 8336 can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.. This analyser's functions make it the ideal instrument for preventive or corrective maintenance. It can also be used to perform a complete energy survey of an installation.For sizing installations or troubleshooting switching faults, the C.A 8336 is equipped with Inrush and TrueInrush functions.Easy to handle and particularly compact, this instrument also offers a large number of calculated values and several processing functions. The C.A 8336 is equipped with 4 voltage measurement channels and 4 current measurement channels. The C.A 8336 captures and records all the parameters, transients, alarms and waveforms simultaneously.When current sensors are connected to the C.A 8336, it recognizes them automatically. It also offers the possibility of mixing different types of current sensors and configuration of the ratios allows direct reading of the measurements.Specially designed for work in the field: Direct access to the main functions (configuration, etc.) Direct access to the measurements (harmonics, flicker, etc.) Voltage/current inputs equipped with colour-coded inserts Large colour TFT screen for easy reading Battery life: 13 hrs The multiple functions of the Qualistar+ C.A 8336 make it a versatile instrument. It is suitable for applications up to 1,000 V in CAT III and 600 V in CAT IV.SoftwareThe measurements obtained with the Qualistar models can be processed using two software tools: PAT delivered as standard and Dataview®, available as an option. They allow configuration, transfers, processing and analysis. In addition, Dataview® offers the possibility of generating reports according to the voltage quality standards. Specific accessories The ESSAILEC cable can be used to carry out tests without disturbing or interrupting the power supply circuit on the meters and the protection relays installed in the secondary circuits of current or voltage transformers. All the Qualistar+ models are delivered with a set of rings/inserts for quick identification and customization of the colour coding for each country. Large choice of current sensors for current measurements from 5 mA to 10 kATechnical specifications: TRMS AC+DC voltage up to 1,000 V TRMS AC+DC current: 5 mA to 10 kA depending on the sensors Frequency Power values: W, VA, var, VAD, PF, DPF, cos φ, tan φ Energy values: Wh, varh, VAh, VADh, BTU, toe, Joule, Harmonics from 0 to the 50th order, phase Transients: up to 210 Inrush with waveform over a period > 10 minutes TrueInrush function Recording of a selection of parameters at the maximum sampling rate for several days to several weeks Alarms: 10,000 of 40 different types Peak detection Vectorial representation Available in more than 27 languages IP53 / IK08 USB communication IEC 61000-4-30 Class B Dimensions / weight: 240 x 180 x 55 mm / 1.9 kg

Advantages Real-time display of waveforms, harmonics, power and recordings Trend recording on several hundred different parameters over a period of weeks Storage of thousands of Alarm events Capture of transients lasting as little as a few µs Load Inrush capture Description The Qualistar+ electrical network power and quality analyser can be used for quick testing of your electrical network and effective analysis of the results. As well as a few minor improvements, version V4 of the Qualistar+ includes several major new functions: Inrush 10 min: the instrument stores a 10-minute Inrush recording for all the voltages, the current and the frequency. Recording of Peakvalues: the Peak + and - values are now recorded. Night mode: a display mode with a black screen background for greater user comfort. Users can choose the type of display to suit their preferences. Specially designed to save time! Ideal for the needs of inspection and maintenance departments, the Qualistar models are designed for quick verification of network quality and simple processing of the results. The keyboard is divided into immediately-identifiable areas (direct functions, Pop-up menus, cursor, etc.) and the wide colour screen (diagonal 148 mm) uses the same pictograms as the keyboard. The display modes are structured. These direct-access functions help save extra time. The Qualistar models are handheld instruments but can also be set up on their fold-away stand, which can prove useful for recording campaigns lasting a long time. In addition, the Qualistar+ includes colour-coded rings to fix to each end of the measurement leads so that the connections are easy to identify. And more than 25 languages are already available.

Advantages Direct access to the main functions (configuration, etc.) Direct access to the measurements (harmonics, flicker, etc.) Voltage/current inputs with colour-coded inserts Large colour TFT screen for easy reading Battery life of 13 hrs Description All the parameters simultaneouslyDesigned for test and maintenance departments working in industrial or administrative buildings, the Qualistar+ C.A 8333 can be used to obtain a snapshot of the main features characterizing the quality of the electrical network.. This analyser's functions make it the ideal instrument for preventive or corrective maintenance. It can also be used to perform a complete energy survey of an installation.For sizing installations or troubleshooting switching faults, the C.A 8333 is equipped with a transient mode which allows users to measure the inrush current over 4 periods.Easy to handle and particularly compact, this instrument also offers a large number of calculated values and several processing functions. The C.A 8333 is equipped with 3 voltage measurement channels and 3 current measurement channels. The C.A 8333 captures and records all the parameters, transients, alarms and waveforms simultaneously.When current sensors are connected to the C.A 8333, it recognizes them automatically. It also offers the possibility of mixing different types of current sensors and configuration of the ratios allows direct reading of the measurements.Specially designed for work in the field:The multiple functions of the Qualistar+ C.A 8333 make it a versatile instrument. It is suitable for applications up to 1,000 V in CAT III and 600 V in CAT IV.SoftwareThe measurements obtained with the Qualistar models can be processed using two software tools: PAT delivered as standard and Dataview®, available as an option. They allow configuration, transfers, processing and analysis. In addition, Dataview® offers the possibility of generating reports according to the voltage quality standards. Specific accessories The ESSAILEC cable can be used to carry out tests without disturbing or interrupting the power supply circuit on the meters and the protection relays installed in the secondary circuits of current or voltage transformers. All the Qualistar+ models are delivered with a set of rings/inserts for quick identification and customization of the colour coding for each country. Large choice of current sensors for current measurements from 5 mA to 10 kATechnical specifications: TRMS AC+DC voltage up to 1,000 V TRMS AC+DC current: 5 mA to 10 kA depending on the sensors Frequency Power values: W, VA, var, VAD, PF, DPF, cos φ, tan φ Energy values: Wh, varh, VAh, VADh, BTU, toe, Joule, Harmonics from 0 to the 50th order, phase Transients: up to 50 Inrush over 4 periods Recording of a selection of parameters at the maximum sampling rate for several days to several weeks Alarms: 4,000 of 10 different types Peak detection Vectorial representation Available in more than 27 languages IP53 / IK08 USB communication IEC 61000-4-30 Class B Dimensions / weight: 240 x 180 x 55 mm / 1.9 kg

Advantages Electrical network power analyser Harmonic decomposition Trend recorder Alarm capture Inrush current Description All your power measurements in parallel! The C.A 8230 single-phase or balanced three-phase power analyser is economical and extremely easy to use. Equipped with direct access to its various functions, it provides greater safety as it automatically recognises the type of connected sensor. It is ideal for on-site or bench-top use. It provides you with all the power measurements you need. It will enable you to measure and qualify your electrical network harmonics. An Inrush mode for starter currents will show your waveform in detail during several seconds. Like its big brother, the Qualistar, the C.A 8230 has a recording mode and a trigger mode for alarms. Functions Voltage range: 6 V RMS to 600 V RMS AC+DC AC current range: 5 mA to 6,500 A DC current range: 1 A to 1,700 A Values: Min, Max, Avg, Peak (+ and -), CF Power values: W, VA, var, DF, THD, cos φ, tan φ Energy: Wh, VAh, varh Harmonics: up to the 50th order Inrush waveform: 18 s IEC 61010 CAT III - 600V  

Advantages Power and electric motor analyser Voltage, current and power measurements Harmonic decomposition Temperature Rotation speed Description POWER AND MOTOR MAINTENANCE ANALYSERAdd the energy function to your C.A 8220 Firmly geared towards electrotechnics and the verification of rotating machinery, the C.A 8220 is intended for companies' testing and maintenance teams.Equipped with a segmented liquid crystal display, compact and shock-resistant, its ergonomic human-machine interface makes it simple and pleasant to use because it is intuitive. Like the C.A 8230, the C.A 8220 can be used to obtain a snapshot of the main characteristics of a single-phase or balanced three-phase network. It also measures all the characteristics needed to check rotating machinery.It allows accurate measurements from a few millamperes to several kiloamperes, as required, by means of a wide range of sensors.Other features: Rotation speed: predictive maintenance requires regular verification of the rotation speed of rotating machinery. The C.A 8220, an all-in-one instrument, fulfils this need simply and efficiently. Temperature: the motors and rotating machinery currently used are equipped with temperature probes which are easily accessible on a terminal block. This makes it possible to measure the motor's internal temperature directly by simply connecting the C.A 8220 to this terminal block.  

Handheld Multifunctional Oscilloscope MS200/MS300/MS500 Product overview •5.7 inches TFT LCD touch screen,640*480 high resolution •70MHz~200MHz selectable bandwidth, up to 190,000wfms/s capture rate •1GS/s real time sampling rate, 240Kpts memory depth •3 operation modes for moving waveform: By touching,Button, Scroll wheel •Optional electronically isolated-inputs •Intergrate the functions of oscilloscope,multi-meter and recorder in one unit •Up to 4~5H Li-ion battery  persistence working time •Support serial trigger and decode for UART/RS232/RS422/RS485,LIN,CAN,SPI,I2C •Support I/O Interface of USB,HDTV trigger for PAL,NTSC,SECAM,720P,1080I,1080P Specifications   MS300 Series (Isolated) MS200 Series MS500 Series (Isolated) MS200 Series Model Bandwidth Real time sample rate Rise time Memory depth Channel Touch operation Series bus  trigger MS207T 70MHz 1GSa/s ≤5ns 240Kpts 2CH YES YES MS210T 100MHz 1GSa/s ≤3.5ns 240Kpts 2CH YES YES MS215T 150MHz 1GSa/s ≤2.33ns 240Kpts 2CH YES YES MS220T 200MHz 1GSa/s ≤1.75ns 240Kpts 2CH YES YES MS300 Series Model Bandwidth Real time Sample Rate Rise Time Memory Depth Channel Touch operation Serial bus  trigger Max waveform capture MS310IT 100MHz 1GSa/s ≤3.5ns 240Kpts 2CH YES YES -（can be upgraded to 50K wfms/s） MS320IT 200MHz 1GSa/s ≤1.75ns 240Kpts 2CH YES YES -（can be upgraded to 50K wfms/s） MS500 Series Model Bandwidth Real time sampling rate Rise time Memory depth Max capture rate Channel Touch operation Serial  bus trigger Serial bus  decode MS510IT 100MHz 1GSa/s ≤3.5ns 240Kpts 190,000wfms/s 2CH YES YES NO MS510S 100MHz 1GSa/s ≤3.5ns 240Kpts 190,000wfms/s 2CH YES YES YES MS520IT 200MHz 1GSa/s ≤1.75ns 240Kpts 190,000wfms/s 2CH YES YES NO MS520S 200MHz 1GSa/s ≤1.75ns 240Kpts 190,000wfms/s 2CH YES YES YES   Standard Accesories   •Multimeter table pen line  •Banana Jack  •7.4V 6000mAh  lithium battery  •Power adapter:                                                                                                          Input:100-240V AC,50-60Hz,                                                                                     Output:12V DC.5A  •USB cable : Mini USB 2.0  •Basic ScopeSuite Software